- 您现在的位置：买卖IC网 > PDF目录3351 > MAX4475AUT/V+T (Maxim Integrated Products)IC OPAMP GP R-R 10MHZ LN SOT23-6 PDF资料下载
参数资料
| 型号： | MAX4475AUT/V+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/21页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP GP R-R 10MHZ LN SOT23-6 |
| 其它有关文件： | Automotive Product Guide |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 放大器类型： | 通用 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 3 V/µs |
| 增益带宽积： | 10MHz |
| 电流 - 输入偏压： | 1pA |
| 电压 - 输入偏移： | 70µV |
| 电流 - 电源： | 2.5mA |
| 电流 - 输出 / 通道： | 48mA |
| 电压 - 电源，单路/双路(±)： | 2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-6 |
| 包装： | 带卷 (TR) |
MAX4475–MAX4478/MAX4488/MAX4489
SOT23, Low-Noise, Low-Distortion,
Wide-Band, Rail-to-Rail Op Amps
10
Maxim Integrated
Low Noise
The amplifier’s input-referred noise-voltage density is
dominated by flicker noise at lower frequencies, and by
thermal noise at higher frequencies. Because the ther-
mal noise contribution is affected by the parallel combi-
nation of the feedback resistive network (RF || RG,
Figure 1), these resistors should be reduced in cases
where the system bandwidth is large and thermal noise
is dominant. This noise contribution factor decreases,
however, with increasing gain settings.
For example, the input noise-voltage density of the cir-
cuit with RF = 100k, RG = 11k (AV = +5V/V) is
en = 14nV/√Hz, en can be reduced to 6nV/√Hz by
choosing RF = 10k, RG = 1.1k (AV = +5V/V), at the
expense of greater current consumption and potentially
higher distortion. For a gain of 100V/V with RF = 100k,
RG = 1.1k, the en is still a low 6nV/√Hz.
Using a Feed-Forward Compensation
Capacitor, CZ
The amplifier’s input capacitance is 10pF. If the resis-
tance seen by the inverting input is large (feedback
network), this can introduce a pole within the amplifier’s
bandwidth resulting in reduced phase margin.
Compensate the reduced phase margin by introducing
a feed-forward capacitor (CZ) between the inverting
input and the output (Figure 1). This effectively cancels
the pole from the inverting input of the amplifier.
Choose the value of CZ as follows:
CZ = 10 x (RF / RG) [pF]
In the unity-gain stable MAX4475–MAX4478, the use of
a proper CZ is most important for AV = +2V/V, and
AV = -1V/V. In the decompensated MAX4488/
MAX4489, CZ is most important for AV = +10V/V.
Figures 2a and 2b show transient response both with
and without CZ.
Using a slightly smaller CZ than suggested by the for-
mula above achieves a higher bandwidth at the
expense of reduced phase and gain margin. As a gen-
eral guideline, consider using CZ for cases where RG ||
RF is greater than 20k (MAX4475–MAX4478) or
greater than 5k
(MAX4488/MAX4489).
Applications Information
The MAX4475–MAX4478/MAX4488/MAX4489 combine
good driving capability with ground-sensing input and
rail-to-rail output operation. With their low distortion and
low noise, they are ideal for use in ADC buffers, med-
ical instrumentation systems and other noise-sensitive
applications.
Ground-Sensing and Rail-to-Rail Outputs
The common-mode input range of these devices
extends below ground, and offers excellent common-
mode rejection. These devices are guaranteed not to
undergo phase reversal when the input is overdriven
(Figure 3).
Figure 4 showcases the true rail-to-rail output operation
of the amplifier, configured with AV = 5V/V. The output
swings to within 8mV of the supplies with a 10k
load,
making the devices ideal in low-supply voltage applica-
tions.
Power Supplies and Layout
The MAX4475–MAX4478/MAX4488/MAX4489 operate
from a single +2.7V to +5.5V power supply or from dual
supplies of ±1.35V to ±2.75V. For single-supply opera-
tion, bypass the power supply with a 0.1F ceramic
VOUT
2V/div
VIN
2V/div
0V
AV = +1
VDD = +5V
RL = 10k
40
s/div
VOUT
1V/div
5V
0V
20
s/div
Figure 3. Overdriven Input Showing No Phase Reversal
Figure 4. Rail-to-Rail Output Operation
相关PDF资料 |
PDF描述 |
|---|---|
| 1.5KE75C-E3/73 | TVS BIDIR 1.5KW 75V 10% 1.5KE |
| 1.5KE75-E3/73 | TVS UNIDIR 1.5KW 75V 10% 1.5KE |
| MQ 3.5 TR | FUSE 125V FAST AXL MQ T/R 3.5A |
| 1.5KE6.8HE3/73 | TVS UNIDIR 1.5KW 6.8V 10% 1.5KE |
| MQ 300 | FUSE 300MA 125V FAST AXL BULK MQ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX4476ATT+ | 制造商:Maxim Integrated Products 功能描述:OP AMP SGL GP R-R O/P 5.5V 6TDFN EP - Rail/Tube |
| MAX4476ATT+T | 功能描述:运算放大器 - 运放 Wide-Band Rail-Rail RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| MAX4476AUT | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX4476AUT#G16 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX4476AUT#TG16 | 功能描述:运算放大器 - 运放 Wide-Band Rail-Rail RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。