![](http://datasheet.mmic.net.cn/Maxim-Integrated-Products/MAX4520EUT-T_datasheet_98336/MAX4520EUT-T_2.png)
MAX451
0
/MAX452
0
Rail-to-Rail, Fault-Protected,
SPST Analog Switches
2
_______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS—Dual Supplies
(V+ = +15V, V- = -15V, GND = 0, VIH = 2.4V, VIL = 0.8V, TA =TMIN to TMAX, unless otherwise noted. Typical values are at TA =
+25°C.) (Note 3)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Note 1: COM and IN pins are not fault protected. Signals on COM or IN exceeding V+ or V- are clamped by internal diodes. Limit
forward diode current to maximum current rating.
Note 2: NC and NO pins are fault protected. Signals on NC or NO exceeding -36V to +36V may damage the device. These limits
apply with power applied to V+ or V-, or ±40V with V+ = V- = 0.
(Voltages Referenced to GND)
V+ ........................................................................-0.3V to +44.0V
V- .........................................................................-44.0V to +0.3V
V+ to V-................................................................-0.3V to +44.0V
COM, IN (Note 1)..................................(V- - 0.3V) to (V+ + 0.3V)
NC, NO (Note 2) .....................................(V+ - 36V) to (V- + 36V)
NC, NO to COM.......................................................-36V to +36V
Continuous Current into Any Terminal..............................±30mA
Peak Current into Any Terminal
(pulsed at 1ms, 10% duty cycle)...................................±50mA
Continuous Power Dissipation (TA = +70°C) (Note 2)
6-Pin SOT23-6 (derate 7.1mW/°C above +70°C) .........696mW
8-Pin MAX (derate 4.10mW/°C above +70°C) ............330mW
Operating Temperature Ranges
MAX45_0EUT....................................................-40°C to +85°C
MAX45_0EUA ...................................................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
E
+25°C
-20
0.1
20
-200
200
NO or NC Input Leakage
Current, Supplies Off
INO, INC
nA
VNO or VNC = ±40V,
V+ = 0, V- = 0
E
+25°C
-20
20
-200
200
NO or NC Input Leakage
Current, Supplies On
INO, INC
nA
VNO or VNC = ±36V,
VCOM = –
+
10V
E
VNO or VNC = -36V
+25°C
811
13
-12
-10
-7
Clamp Output Current,
Supplies On
ICOM
mA
VNO or VNC = 36V
+25°C
-10
10
-200
200
COM Off-Leakage Current,
Supplies On
ICOM(OFF)
nA
VNO or VNC = ±36V
Applies with power off (Note 6)
E
-36
36
-40
40
Fault-Protected Analog
Signal Range
VNO, VNC
V
Applies with power on (Note 6)
-20
20
E
-10
10
+25°C
E
-10
10
E
225
E
125
160
+25°C
-0.5
0.01
0.5
COM On-Leakage Current
(Notes 4, 5)
ICOM(ON)
nA
VCOM = ±14V; VNO, VNC =
±14V or unconnected
+25°C
-0.5
0.01
0.5
INO(OFF),
INC(OFF)
nA
NO or NC Off-Leakage Current
(Notes 4, 5)
VCOM = ±14V;
VNO, VCOM = –
+14V
COM Off-Leakage Current
(Notes 4, 5)
+25°C
Fault-Free Analog Signal Range
VNO, VNC
V-
V+
V
E
Applies with power on or off
TA
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS
On-Resistance
RON
-0.5
0.01
0.5
ICOM(OFF)
nA
CONDITIONS
VCOM = ±10V, ICOM = 1mA
VCOM = ±14V;
VNO, VNC = –
+
14V
ANALOG SWITCH
FAULT (V+ = +15V, V- = -15V, unless otherwise noted.)