参数资料
| 型号： | MAX4520EUT-T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/12页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH SPST SOT23-6 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 开关 |
| 电路： | 1 x SPST- NO |
| 导通状态电阻： | 390 欧姆 |
| 电压电源： | 单/双电源 |
| 电压 - 电源，单路/双路(±)： | 9 V ~ 36 V，±4.5 V ~ 20 V |
| 电流 - 电源： | 50µA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-6 |
| 包装： | 带卷 (TR) |
MAX451
0
/MAX452
0
Rail-to-Rail, Fault-Protected,
SPST Analog Switches
_______________________________________________________________________________________
9
Normal Operation
Two comparators continuously compare the voltage on
the NO (or NC) pin with V+ and V-. When the signal on
NO or NC is between V+ and V-, the switch acts nor-
mally, with FETs N1 and P1 turning on and off in
response to IN signals. The parallel combination of N1
and P1 forms a low-value resistor between NO (or NC)
and COM so that signals pass equally well in either
direction.
Positive Fault Condition
When the signal on NO (or NC) exceeds V+ by about
50mV, the high-fault comparator output is high, turning
off FETs N1 and P1. This makes the NO (or NC) pin
high impedance regardless of the switch state. If the
switch state is “off,” all FETs are turned off and both NO
(or NC) and COM are high impedance. If the switch
state is “on,” FET P2 is turned on, sourcing current from
V+ to COM.
Negative Fault Condition
When the signal on NO (or NC) exceeds V- by about
50mV, the low-fault comparator output is high, turning
off FETs N1 and P1. This makes the NO (or NC) pin
high impedance regardless of the switch state. If the
switch state is “off,” all FETs are turned off and both NO
(or NC) and COM are high impedance. If the switch
state is “on,” FET N2 is turned on, sinking current from
COM to V-.
Transient Fault Response and Recovery
When a fast rise-time and fall-time transient on IN
exceeds V+ or V-, the output (COM) follows the input (IN)
to the supply rail with only a few nanoseconds delay.
This delay is due to the switch on-resistance and circuit
capacitance to ground. When the input transient returns
to within the supply rails, however, there is a longer out-
put recovery time delay. For positive faults, the recovery
time is typically 3.5s. For negative faults, the recovery
time is typically 1.3s. These values depend on the COM
output resistance and capacitance. The delays are not
dependent on the fault amplitude. Higher COM output
resistance and capacitance increase recovery times.
COM and IN Pins
FETs N2 and P2 can source about ±13mA from V+ or V-
to the COM pin in the fault condition. Ensure that if the
COM pin is connected to a low-resistance load, the
absolute maximum current rating of 30mA is never
exceeded, both in normal and fault conditions.
The GND, COM, and IN pins do not have fault protec-
tion. Reverse ESD-protection diodes are internally con-
nected between GND, COM, IN, and both V+ and V-. If a
signal on GND, COM, or IN exceeds V+ or V- by more
than 300mV, one of these diodes will conduct heavily.
During normal operation these reverse-biased ESD
diodes leak a few nanoamps of current to V+ and V-.
Fault-Protection Voltage and Power Off
The maximum fault voltage on the NC or NO pins is
±36V with power applied and ±40V with power off.
Failure Modes
The MAX4510/MAX4520 are not lightning arrestors or
surge protectors.
Exceeding the fault-protection voltage limits on NO or
NC, even for very short periods, can cause the device
to fail.
Ground
There is no connection between the analog signal path
and GND. The analog signal path consists of an N-
channel and P-channel MOSFET with their sources and
drains paralleled and their gates driven out of phase to
V+ and V- by the logic-level translators.
V+ and GND power the internal logic and logic-level
translators and set the input logic thresholds. The logic-
level translators convert the logic levels to switched V+
and V- signals to drive the gates of the analog switch.
This drive signal is the only connection between the
power supplies and the analog signal. GND, IN, and
COM have ESD-protection diodes to V+ and V-.
IN Logic-Level Thresholds
The logic-level thresholds are CMOS and TTL compati-
ble when V+ is +15V. As V+ is raised, the threshold
increases slightly, and when V+ reaches 25V, the level
threshold is about 2.8V—above the TTL output high-
level minimum of 2.4V, but still compatible with CMOS
outputs (see Typical Operating Characteristics).
Increasing V- has no effect on the logic-level thresholds,
but it does increase the gate-drive voltage to the signal
FETs, reducing their on-resistance.
Dual Supplies
The MAX4510/MAX4520 operate with dual supplies
between ±4.5V and ±20V. The V+ and V- supplies
need not be symmetrical, but their difference cannot
exceed the absolute maximum rating of 44V.
Single Supply
The MAX4510/MAX4520 operate from a single supply
between +9V and +36V when V- is connected to GND.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX4523ESE | IC SWITCH QUAD SPST 16SOIC |
| MAX4524LEUB+ | IC MUX/SW ANLG CMOS LV 10UMAX |
| MAX4525EUB | IC MULTIPLEXER 2X2 10UMAX |
| MAX4527ESA | IC SWITCH DUAL SPDT 8SOIC |
| MAX4528EUA | IC SWITCH DUAL SPDT 8UMAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX4521C/D | 功能描述:模拟开关 IC RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| MAX4521C/D DIE | 制造商:Maxim Integrated Products 功能描述: |
| MAX4521CEE | 功能描述:模拟开关 IC RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| MAX4521CEE+ | 功能描述:模拟开关 IC Quad Low-V SPST Analog Switch RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| MAX4521CEE+T | 功能描述:模拟开关 IC Quad Low-V SPST Analog Switch RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
发布紧急采购，3分钟左右您将得到回复。