- 您现在的位置：买卖IC网 > PDF目录11046 > MAX4539CAP (Maxim Integrated Products)IC MULTIPLEXER 8X1 20SSOP PDF资料下载
参数资料
| 型号： | MAX4539CAP |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 5/20页 |
| 文件大小： | 0K |
| 描述： | IC MULTIPLEXER 8X1 20SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 66 |
| 功能： | 多路复用器 |
| 电路： | 1 x 8:1 |
| 导通状态电阻： | 75 欧姆 |
| 电压电源： | 单/双电源 |
| 电压 - 电源，单路/双路(±)： | 2.7 V ~ 12 V，± 2.7 V ~ 6 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 管件 |
MAX4539/MAX4540
Low-Voltage, Single 8-to-1 and
Dual 4-to-1 Cal-Multiplexers
______________________________________________________________________________________
13
Single-Supply Operation
The MAX4539/MAX4540 operate from a single supply
between +2.7V and +12V when V- is connected to
GND. All of the bipolar precautions must be observed.
However, these parts are optimized for ±5V operation,
and most AC and DC characteristics are degraded sig-
nificantly when departing from ±5V. As the overall sup-
ply voltage (V+ to V-) is lowered, switching speed,
on-resistance, off isolation, and distortion will degrade.
(see the
Typical Operating Characteristics section).
Single-supply operation also limits signal levels and
interferes with ground referenced signals. When V- = 0,
AC signals are limited to -0.3V. Voltages below -0.3V can
be clipped by the internal ESD-protection diodes, and
the parts can be damaged if excessive current flows.
Power Up
During power up, on-chip latches will strobe whatever
addresses are present if EN goes high before LATCH
reaches a logic high. When this condition occurs, one of
the internal dividers connected between the supplies
may inadvertently turn on, causing higher supply current
(~200A supply current) when the enable input is tog-
gled. Avoid this condition by ensuring that EN pin stays
low until the remaining logic inputs are valid. To accom-
plish this, connect a resistor from EN to ground or apply
a low voltage to EN before the other logic inputs go high.
Power Off
When power to the MAX4539/MAX4540 is off (i.e., V+ =
V- = 0), the Absolute Maximum Ratings still apply. This
means that neither logic-level inputs on NO_ nor sig-
nals on COM_ can exceed ±0.3V. Voltages beyond
±0.3V cause the internal ESD-protection diodes to con-
duct, and the parts can be damaged if excessive cur-
rent flows.
Chip Information
TRANSISTOR COUNT: 561
Test Circuits/Timing Diagrams
50%
tR < 20ns
tF < 20ns
VCOM
V+
0V
VNO1, VNO1B
0V
VNO8, VNO4B
LOGIC
INPUT
VEN
SWITCH
OUTPUT
+5V
-5V
GND
V+
A1
A2
V-
EN
LATCH
CAL
A0
NO1
NO2–NO7
NO8
COM
+3V
-3V
50
MAX4539
300
35pF
A1
A0
+5V
VCOM
-5V
GND
V+
V-
EN
NO1B
NO2B–NO3B
NO1A–NO2A
NO4B
COMB
+3V
50
MAX4540
300
35pF
90%
tTRANS
-3V
LATCH
CAL
Figure 1. Transition Time
相关PDF资料 |
PDF描述 |
|---|---|
| VE-BTZ-IY-F1 | CONVERTER MOD DC/DC 2V 20W |
| VE-BTZ-IX-F3 | CONVERTER MOD DC/DC 2V 30W |
| MAX4537EPE | IC SWITCH QUAD SPST 16DIP |
| VE-BTZ-IX-F2 | CONVERTER MOD DC/DC 2V 30W |
| MAX4537EEE | IC SWITCH QUAD SPST 16QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX4539EAP | 制造商:Maxim Integrated Products 功能描述:LOW-VOLTAGE, 8 TO 1 CALIBRATION-MULTIPLEXER W - Bulk |
| MAX453C/D DIE | 制造商:Maxim Integrated Products 功能描述: |
| MAX453CPA | 功能描述:视频放大器 Integrated Circuits (ICs) RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel |
| MAX453CPA+ | 功能描述:视频放大器 50MHz Video Amp & MUX Amp RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel |
| MAX453CSA | 功能描述:视频放大器 RoHS:否 制造商:ON Semiconductor 通道数量:4 电源类型: 工作电源电压:3.3 V, 5 V 电源电流: 最小工作温度: 最大工作温度: 封装 / 箱体:TSSOP-14 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。