- 您现在的位置：买卖IC网 > PDF目录11164 > MAX4599ELT+T (Maxim Integrated Products)IC SWITCH SPDT 6UDFN PDF资料下载
参数资料
| 型号： | MAX4599ELT+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/9页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH SPDT 6UDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 开关 |
| 电路： | 1 x SPDT |
| 导通状态电阻： | 60 欧姆 |
| 电压电源： | 单电源 |
| 电压 - 电源，单路/双路(±)： | 2 V ~ 5.5 V |
| 电流 - 电源： | 1µA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-WFDFN |
| 供应商设备封装： | 6-uDFN（1.5x1.0） |
| 包装： | 带卷 (TR) |
Applications Information
Analog Signal Levels
Analog signals can range over the supply voltage (V+
to GND) with on-resistance changing very little over the
entire range (see Typical Operating Characteristics).
The MAX4599 is bidirectional, so the NO, NC, and
COM pins can be used either as inputs or outputs.
Power-Supply Sequencing and
Overvoltage Protection
Proper power-supply sequencing is recommended for
all CMOS devices. Always apply V+ before applying
analog signals or logic inputs, especially if the analog
or logic signals are not current limited. If this sequenc-
ing is not possible, and if the analog or logic inputs are
not current limited to < 20mA, add a small-signal diode
(D1) as shown in Figure 1. If the analog signal can dip
below GND, add D2. Adding protection diodes
reduces the analog signal range to a diode drop (about
0.7V) below V+ for D1 or to a diode drop above ground
for D2. The addition of diodes does not affect leakage.
On-resistance increases by a small amount at low sup-
ply voltages. Maximum supply voltage (V+) must not
exceed 6V.
Protection diodes D1 and D2 also protect against some
overvoltage situations. A fault voltage up to the
absolute maximum rating at an analog signal input
does not damage the device, even if the supply voltage
is below the signal voltage.
MAX4599
Low-Voltage, Single-Supply,
SPDT Analog Switch in SC70
6
_______________________________________________________________________________________
-95
0.01
0.1
1
10
100 200
FREQUENCY RESPONSE
-75
MAX4599
toc10
FREQUENCY (MHz)
LOSS
(dB)
-55
-35
-15
-25
-45
-65
-85
-5
ON-RESPONSE
OFF-ISOLATION
Typical Operating Characteristics (continued)
(TA = +25°C, unless otherwise noted.)
1
0.01
0.1
100
110
TOTAL HARMONIC DISTORTION PLUS
NOISE vs. FREQUENCY
0.1
MAX4599
toc11
FREQUENCY (kHz)
THD
+
N
(%)
RL = 600
VIN = 5VP-P
VIN = 3VP-P
NAME
FUNCTION
1
IN
Digital Control Input
2
V+
Positive Supply Voltage
PIN
3
GND
Ground
4
NC
Analog Switch Normally Closed
6
NO
Analog Switch Normally Open
5
COM
Analog Switch Common
Pin Description
POSITIVE SUPPLY
COM
NO
OR
NC
D2
D1
GND
Vg
V+
Figure 1. Overvoltage Protection Using Two External Blocking
Diodes
相关PDF资料 |
PDF描述 |
|---|---|
| MAX4731EBL+T | IC SWITCH DUAL SPST 9UCSP |
| MAX4542EKA+T | IC SWITCH DUAL SPST SOT23-8 |
| VI-B4L-CU-B1 | CONVERTER MOD DC/DC 28V 200W |
| MAX4543EKA+T | IC SWITCH DUAL SPST SOT23-8 |
| VE-B62-IW-F3 | CONVERTER MOD DC/DC 15V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX4599EUT | 制造商:Maxim Integrated Products 功能描述:LOW-VOLTAGE, SINGLE-SUPPLY, SPDT ANALOG SWITC - Rail/Tube |
| MAX4599EUT+ | 制造商:Maxim Integrated Products 功能描述:ANLG SW SGL SPDT 5.5V 6PIN SOT-23 - Rail/Tube |
| MAX4599EUT+T | 功能描述:模拟开关 IC Single-Supply SPDT Analog Switch RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| MAX4599EUT-T | 功能描述:模拟开关 IC Single-Supply SPDT Analog Switch RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| MAX4599EXT | 制造商:Maxim Integrated Products 功能描述:LOW-VOLTAGE SINGLE-SUPPLY SPDT AN - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。