- 您现在的位置：买卖IC网 > PDF目录11393 > MAX4659EUA+ (Maxim Integrated Products)IC SWITCH SPDT 8UMAX PDF资料下载
参数资料
| 型号： | MAX4659EUA+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH SPDT 8UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 功能： | 开关 |
| 电路： | 1 x SPDT |
| 导通状态电阻： | 25 欧姆 |
| 电压电源： | 单/双电源 |
| 电压 - 电源，单路/双路(±)： | 9 V ~ 40 V，±4.5 V ~ 20 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 管件 |
| 产品目录页面： | 1421 (CN2011-ZH PDF) |
MAX4659/MAX4660
High-Current, 25
, SPDT, CMOS
Analog Switches
_______________________________________________________________________________________
7
Detailed Description
The MAX4659/MAX4660 are single, single-pole/double-
throw (SPDT) CMOS analog switches. The CMOS
switch construction provides rail-to-rail signal handling
while consuming very little power. The switch is con-
trolled by a TTL/CMOS level compatible digital input.
The MAX4659/MAX4660 have a normally open switch
and a normally closed switch.
These devices can be operated with either single
power supplies or dual power supplies. Operation at up
to ±20V supplies allows users a wide switching dynam-
ic range. Additionally, asymmetrical operation is possi-
ble to tailor performance to a particular application.
These switches have been specifically designed to
handle high switch currents, up to 200mA peak current
and 150mA continuous currents. In order to do this, a
new technique is used to drive the body of the output
N-channel device. (Note: The basic switch between the
input, NC/NO terminal and the output common terminal
consists of an N-channel MOSFET and a P-channel
MOSFET in parallel.) The standard method limits opera-
tion to approximately a 600mV drop across the switch.
More than 600mV causes an increase in IdON leakage
current (due to the turn-on of on-chip parasitic diodes),
and an increase in V+ supply current. With this new
sensing method, there is no limitation to the voltage
drop across the switch. Current and voltage are limited
only by the power dissipation rating of the package and
the absolute maximum ratings of the switch.
When the analog input voltage drop is approximately
7mV there is an increase in power supply current from
90A to 2mA (typ) within a 1mV to 7mV range, caused
by the new sensing/driving circuitry.
Applications Information
Overvoltage Protection
Proper power-supply sequencing is recommended for
all CMOS devices. Do not exceed the absolute maxi-
mum ratings, because stresses beyond the listed rat-
ings can cause permanent damage to the devices.
First, connect GND, followed by V+, V-, and the remain-
ing pins. If power-supply sequencing is not possible,
add two small-signal diodes (D1, D2) in series with
supply pins (Figure 1). Adding diodes reduces the ana-
log signal range to one diode drop below V+ and one
diode drop above V-, but does not affect the devices’
low switch resistance and low leakage characteristics.
Device operation is unchanged, and the difference
between V+ and V- should not exceed 44V. The protec-
tion diode for the negative supply is not required when
V- is connected to GND.
Off-Isolation at High Frequencies
In 50
systems, the high-frequency on-response of
these parts extends from DC to above 100MHz, with a
typical loss of -2dB. When the switch is turned off, how-
ever, it behaves like a capacitor and off-isolation
decreases with increasing frequency. This effect is
more pronounced with higher source and load imped-
ances. Above 5MHz, circuit board layout becomes criti-
cal. The graphs shown in the Typical Operating
Characteristics were taken using a 50
source and
load connected with BNC connectors.
V+
COM
V-
N_
Vg
V+
D1
D2
V-
Figure 1. Overvoltage Protection Using Blocking Diodes
相关PDF资料 |
PDF描述 |
|---|---|
| MAX323ESA+ | IC SWITCH DUAL SPST 8SOIC |
| VE-26H-EU-B1 | CONVERTER MOD DC/DC 52V 200W |
| MAX325ESA+ | IC SWITCH DUAL SPST 8SOIC |
| VE-26F-EU-B1 | CONVERTER MOD DC/DC 72V 200W |
| MAX320ESA+ | IC SWITCH DUAL SPST 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX4659EUA+ | 功能描述:模拟开关 IC 25Ohm SPST CMOS Analog Switch RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| MAX4659EUA+ | 制造商:Maxim Integrated Products 功能描述:IC ANALOG SWITCH SINGLE |
| MAX4659EUA+T | 功能描述:模拟开关 IC 25Ohm SPST CMOS Analog Switch RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| MAX4659EUA-T | 功能描述:模拟开关 IC RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| MAX465CNG | 功能描述:视频开关 IC RoHS:否 制造商:Texas Instruments 开关数量:4 开启电阻（最大值）:12 Ohms 传播延迟时间: 开启时间（最大值）: 关闭时间（最大值）: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:WQFN-42 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。