- 您现在的位置：买卖IC网 > PDF目录11132 > MAX4693ETE+ (Maxim Integrated Products)IC SWITCH TRIPLE SPDT 16TQFN PDF资料下载
参数资料
| 型号： | MAX4693ETE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 5/21页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH TRIPLE SPDT 16TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 75 |
| 功能： | 开关 |
| 电路： | 3 x SPDT |
| 导通状态电阻： | 70 欧姆 |
| 电压电源： | 单/双电源 |
| 电压 - 电源，单路/双路(±)： | 2.7 V ~ 11 V，±2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WQFN 裸露焊盘 |
| 供应商设备封装： | 16-TQFN-EP（4x4） |
| 包装： | 管件 |
MAX4691–MAX4694
Low-Voltage 8:1 Mux/Dual 4:1 Mux/Triple SPDT/
Quad SPDT in UCSP Package
______________________________________________________________________________________
13
During normal operation, these (and other) reverse-
biased ESD diodes leak, forming the only current drawn
from V+ or V-.
Virtually all the analog leakage current comes from the
ESD diodes. Although the ESD diodes on a given signal
pin are identical, and therefore fairly well balanced,
they are reverse biased differently. Each is biased by
either V+ or V- and the analog signal. This means their
leakages will vary as the signal varies. The
difference in
the two diode leakages to the V+ and V- pins consti-
tutes the analog signal path leakage current. All analog
leakage current flows between each pin and one of the
supply terminals, not to the other switch terminal. This is
why both sides of a given switch can show leakage cur-
rents of either the same or opposite polarity.
V+ and GND power the internal logic and logic-level
translators, and set both the input and output logic lim-
its. The logic-level translators convert the logic levels
into switched V+ and V- signals to drive the gates of the
analog signals. This drive signal is the only connection
between the logic supplies (and signals) and the ana-
log supplies. V+ and V- have ESD-protection diodes on
GND.
Bipolar Supplies
The MAX4691/MAX4692/MAX4693 operate with bipolar
supplies between ±2V and ±5.5V. The V+ and V- sup-
plies need not be symmetrical, but their difference can-
not exceed the absolute maximum rating of +12V.
Single Supply
These devices operate from a single supply between +2V
and +11V when V- is connected to GND. All of the bipolar
precautions must be observed. At room temperature,
they operate with a single supply at near or below +2V,
although as supply voltage decreases, switch on-resis-
tance and switching times become very high.
Always bypass supplies with a 0.1F capacitor.
Overvoltage Protection
Proper power-supply sequencing is recommended for
all CMOS devices. Do not exceed the absolute maxi-
mum ratings, because stresses beyond the listed rat-
ings can cause permanent damage to the devices.
Always sequence V+ on first, then V-, followed by the
logic inputs and by W, X, Y, Z. If power-supply
sequencing is not possible, add two small signal
diodes (D1, D2) in series with the supply pins for over-
voltage protection (Figure 1).
Adding diodes reduces the analog signal range to one
diode drop below V+ and one diode drop above V-, but
does not affect the devices’ low switch resistance and
low leakage characteristics. Device operation is
unchanged, and the difference between V+ and V-
should not exceed 12V. These protection diodes are
not recommended when using a single supply if signal
levels must extend to ground.
UCSP Reliability
The chip-scale package (UCSP) represents a unique
package that greatly reduces board space compared to
other packages. UCSP reliability is integrally linked to the
user’s assembly methods, circuit board material, and
usage environment. The user should closely review these
areas when considering a UCSP. Performance through
Operating Life Test and Moisture Resistance is equal to
conventional package technology as it is primarily deter-
mined by the wafer-fabrication process. However, this
form factor may not perform equally to a packaged prod-
uct through traditional mechanical reliability tests.
Mechanical stress performance is a greater considera-
tion for a UCSP. UCSP solder joint contact integrity
must be considered since the package is attached
through direct solder contact to the user’s PC board.
Testing done to characterize the UCSP reliability per-
formance shows that it is capable of performing reli-
ably through environmental stresses. Results of
environmental stress tests and additional usage data
and recommendations are detailed in the UCSP appli-
cation note, which can be found on Maxim’s website,
at www.maxim-ic.com.
( ) ARE FOR THE MAX4694 ONLY, REPLACE V- WITH GND.
MAX4691
MAX4692
MAX4693
MAX4694
COM
NO
V-
(GND)
V+
*INTERNAL PROTECTION DIODES
D2
D1
EXTERNAL BLOCKING DIODE
V- (GND )
V+
*
Figure 1. Overvoltage Protection
相关PDF资料 |
PDF描述 |
|---|---|
| MAX4694ETE+ | IC SWITCH QUAD SPDT 16TQFN |
| VI-B6D-IW-F4 | CONVERTER MOD DC/DC 85V 100W |
| DG442DY+T | IC SWITCH QUAD SPST 16SOIC |
| VE-BWM-IY-F3 | CONVERTER MOD DC/DC 10V 50W |
| C8051F510-IM | IC 8051 MCU 32K FLASH 40-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX4693ETE+ | 功能描述:模拟开关 IC 3Ch SPDT Low V Analog Switch RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| MAX4693ETE+T | 功能描述:模拟开关 IC 3Ch SPDT Low V Analog Switch RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| MAX4694EBE | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube 制造商:Rochester Electronics LLC 功能描述: |
| MAX4694EBE+ | 制造商:Maxim Integrated Products 功能描述:ANLG SW QUAD SPDT 5.5V/11V 16UCSP - Rail/Tube |
| MAX4694EBE+T | 功能描述:模拟开关 IC 4Ch SPDT Low V Analog Switch RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
发布紧急采购，3分钟左右您将得到回复。