
MAX4717/MAX4718
4.5
/20, 300MHz Bandwidth, Dual SPDT
Analog Switches in UCSP
2
_______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS—Single +3V Supply
(V+ = +2.7V to +3.6V, VIH = +1.4V, VIL = +0.5V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at V+ = +3.0V,
TA = +25°C, unless otherwise noted.) (Notes 2, 3)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
(All voltages are referenced to GND.)
V+, IN_...................................................................-0.3V to +6.0V
COM_, NO_, NC_ (Note 1) ...........................-0.3V to (V+ + 0.3V)
Continuous Current COM_, NO_, NC_ ...........................±100mA
Peak Current COM_, NO_, NC_
(pulsed at 1ms, 10% duty cycle)................................±200mA
Continuous Power Dissipation (TA = +70°C)
10-Pin MAX (derate 5.6mW/°C above +70°C) ...........444mW
10-Pin TDFN (derate 24.4mW/°C above +70°C) .......1951mW
12-Bump UCSP (derate 11.4mW/°C above +70°C) ....909mW
ESD Method 3015.7 .............................................................>2kV
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Bump Temperature (soldering)
Infrared (15s) ...............................................................+220°C
Vapor Phase (60s) .......................................................+215°C
Note 1: Signals on COM_, NO_, or NC_ exceeding V+ or GND are clamped by internal diodes. Limit forward-diode current to
maximum current rating.
PARAMETER
SYMBOL
CONDITIONS
TA
MIN
TYP
MAX
UNITS
Analog Signal Range
VCOM_,
VNO_, VNC_
TMIN to
TMAX
0V+
V
ANALOG SWITCH (Low RON—MAX4717/MAX4718 SPDT 1)
+25°C
3.0
4.5
On-Resistance
(Note 4)
RON
V+ = 2.7V, ICOM_ = 10mA;
VNO_ or VNC_ = 1.5V
TMIN to
TMAX
5
+25°C
0.1
0.3
On-Resistance Match Between
Channels (Notes 4, 5)
RON
V+ = 2.7V, ICOM_ = 10mA;
VNO_ or VNC_ = 1.5V
TMIN to
TMAX
0.4
+25°C
0.6
1.2
On-Resistance Flatness
(Note 6)
RFLAT(ON)
V+ = 2.7V, ICOM_ = 10mA;
VNO_ or VNC_ = 1.0V, 1.5V, 2.0V
TMIN to
TMAX
1.5
+25°C
-0.5
+0.01
+0.5
NO_, NC_ Off-Leakage Current
(Note 7)
INO_(OFF),
INC_(OFF)
V+ = 3.6V, VCOM_ = 0.3V, 3.3V;
VNO_ or VNC_ = 3.3V, 0.3V
TMIN to
TMAX
-1
+1
nA
+25°C
-1
+0.01
+1
COM_ On-Leakage Current
(Note 7)
ICOM_(ON)
V+ = 3.6V, VCOM_ = 0.3V, 3.3V;
VNO_ or VNC_ = 0.3V, 3.3V, or
floating
TMIN to
TMAX
-2
+2
nA
ANALOG SWITCH (High RON—MAX4718 SPDT 2)
+25°C
15
20
On-Resistance (Note 4)
RON
V+ = 2.7V, ICOM_ = 10mA;
VNO_ or VNC_ = 1.5V
TMIN to
TMAX
25