- 您现在的位置：买卖IC网 > PDF目录1942 > MAX4732EUA+T (Maxim Integrated Products)IC SWITCH DUAL SPST 8UMAX PDF资料下载
参数资料
| 型号： | MAX4732EUA+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/14页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH DUAL SPST 8UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 开关 |
| 电路： | 2 x SPST - NC |
| 导通状态电阻： | 50 欧姆 |
| 电压电源： | 单电源 |
| 电压 - 电源，单路/双路(±)： | 2 V ~ 11 V |
| 电流 - 电源： | 1µA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 带卷 (TR) |
MAX4731/MAX4732/MAX4733
Analog Signal Levels
Analog signals that range over the entire supply voltage
(GND to V+) pass with very little change in RON (see
Typical Operating Characteristics). The bidirectional
switches allow NO_, NC_, and COM_ connections to be
used as either inputs or outputs.
Power-Supply Sequencing and
Overvoltage Protection
CAUTION: Do not exceed the absolute maximum
ratings. Stresses beyond the listed ratings can
cause permanent damage to the devices.
Proper power-supply sequencing is recommended for
all CMOS devices. Always apply V+ before applying
analog signals, especially if the analog signal is not
current limited. If this sequencing is not possible, and if
the analog inputs are not current limited to < 20mA,
add a small-signal diode, D1, as shown in Figure 1. If
the analog signal can dip below GND, add D2. Adding
protection diodes reduces the analog signal range to a
diode drop (about 0.7V) below V+ (for D1), and to a
diode drop above ground (for D2). Leakage is unaffect-
ed by adding the diodes. On-resistance increases
slightly at low supply voltages. Maximum supply volt-
age (V+) must not exceed +11V.
Adding protection diodes causes the logic thresholds to
be shifted relative to the power-supply rails. The most
significant shift occurs when using low supply voltages
(+5V or less). With a +5V supply, TTL compatibility is not
guaranteed when protection diodes are added. Driving
IN1 and IN2 all the way to the supply rails (i.e., to a
diode drop higher than the V+ pin, or to a diode drop
lower than the GND pin) is always acceptable.
Protection diodes D1 and D2 also protect against some
overvoltage situations. Using the circuit in Figure 1, no
damage results if the supply voltage is below the
absolute maximum rating (+12V) and if a fault voltage
up to the absolute maximum rating (V+ + 0.3V) is
applied to an analog signal terminal.
UCSP Applications Information
For the latest application details on USCP construction,
dimensions, tape carrier information, printed circuit
board techniques, bump-pad layout, and recommend-
ed reflow temperature profile as well as the latest infor-
mation on reliability testing results, go to the Maxim
web site at www.maxim-ic.com/ucsp to find the
Application Note: UCSP—A Wafer-Level Chip-Scale
Package.
50
, Dual SPST Analog Switches in UCSP
8
_______________________________________________________________________________________
MAX4731
MAX4732
MAX4733
NO_
COM_
GND
V+
*INTERNAL PROTECTION DIODES.
D2
D1
EXTERNAL BLOCKING DIODE
GND
V+
*
Figure 1. Overvoltage Protection Using External Blocking Diodes
Test Circuits/Timing Diagrams
相关PDF资料 |
PDF描述 |
|---|---|
| MAX4734EGC+ | IC MULTIPLEXER 4X1 12QFN |
| MAX4736ETC+ | IC SWITCH DUAL SPDT 12TQFN |
| MAX4738EUD+ | IC SWITCH QUAD SPST 14TSSOP |
| MAX4740ETE+ | IC SWITCH QUAD SPDT 16TQFN |
| MAX4742EUA+ | IC SWITCH ANLG DUAL SPST 8UMAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX4733EBL | 制造商:Maxim Integrated Products 功能描述:ANALOG SWITCH, DUAL, SPST,1 NC SWITCH, 9 PIN PLASTIB BGA LE - Rail/Tube |
| MAX4733EBL+ | 制造商:Maxim Integrated Products 功能描述:ANALOG SWITCH, DUAL, SPST, 1 NC SWITCH, 9 PIN PLASTIC BGA - Rail/Tube |
| MAX4733EBL+T | 制造商:Maxim Integrated Products 功能描述:ANLG SW DUAL SPST 11V 9UCSP - Rail/Tube |
| MAX4733EBL-T | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX4733ETA+ | 制造商:Maxim Integrated Products 功能描述:50OHM DUAL SPST ANALOG SWITCHES IN - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。