- 您现在的位置：买卖IC网 > PDF目录11039 > MAX4815ETE+ (Maxim Integrated Products)IC SWITCH QUAD SPST 16TQFN PDF资料下载
参数资料
| 型号： | MAX4815ETE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 17/17页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH QUAD SPST 16TQFN |
| 产品变化通告： | Product Discontinuation 01/Jun/2011 |
| 标准包装： | 60 |
| 功能： | 开关 |
| 电路： | 4 x SPST - NC |
| 导通状态电阻： | 5 欧姆 |
| 电压电源： | 单/双电源 |
| 电压 - 电源，单路/双路(±)： | 6 V ~ 11 V，±3.3 V ~ 5 V |
| 电流 - 电源： | 800nA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WQFN 裸露焊盘 |
| 供应商设备封装： | 16-TQFN-EP（5x5） |
| 包装： | 管件 |
Detailed Description
The MAX4815/MAX4816/MAX4817 are high-bandwidth,
low-on-resistance, quad-SPST analog switches targeted
to serve as integrated T1/E1 analog protection switches
for 1+1 and N+1 line-card redundancy applications.
These devices are designed to replace electromechani-
cal relays to save board space, reduce power consump-
tion, and simplify PC board routing. The devices allow
the user to live insert the boards with no adverse effects.
The MAX4815/MAX4816/MAX4817 support ±3.3V or
±5V dual-supply operation, which is required for E1/T1
signal switching in the line-side of the interface trans-
former. Internal voltage multipliers supply the switches
yielding excellent linearity and low on-resistance, typi-
cally 3.7
Ω, within the E1/T1 analog signal range. This
high-bandwidth, typically 550MHz, family of devices is
optimized for low return loss and matched pulse tem-
plate performance in E1/T1 short-haul and long-haul
applications.
Analog Signal Levels
The on-resistance of the MAX4815/MAX4816/MAX4817 is
very low and stable as the analog signals are swept from
V- to V+ (see the Typical Operating Characteristics).
Fault Protection
The fault protection of the MAX4815/MAX4816/
MAX4817 allows the devices to handle input signals of
more than twice the supply voltage without clamping
the signal, latching up, or disturbing other cards in the
system. The device detects when the input voltage
drops below the negative supply. As soon as a fault
condition is detected, the switch is immediately turned
off for 128 clock cycles (typically 128s). At the end of
the 128s timeout, the switch is turned back on for one
clock cycle. At the end of the one clock cycle, if the sig-
nal is within the operating range, the switch will remain
on. Otherwise, the device will turn the switch off again
for 128 clock cycles. This will repeat until the signal is
within the operating range. In T1/E1 redundancy appli-
cations, this can happen when the load resistor (RL) is
removed or disconnected for any reason, as shown in
Figure 1. Without a load resistor, the output voltage
when using a 1:2 transformer can be as high as ±11V.
Hot Insertion
The MAX4815/MAX4816/MAX4817 tolerate hot inser-
tions, thus are not damaged when inserted into a live
backplane. Competing devices can exhibit low imped-
ance when plugged into a live backplane that can
cause high power dissipation leading to damage of the
device itself. The MAX4815/MAX4816/MAX4817 have
relatively high input impedance when V+ and V- are
unconnected or connected to GND. Therefore, the
devices are not destroyed by a hot insertion. In order to
guarantee data integrity, the V+ and V- supplies must
be properly biased.
Applications Information
T1/E1 N+1 Redundancy
The MAX4815/MAX4816/MAX4817 are designed for
adjacent line-card protection applications. Figures 6 and
7 show a basic architecture for twisted-pair interface
(120
Ω E1, or 100Ω T1). Coaxial cable interface (75Ω E1)
can be illustrated with the same figures but without the
single-ended-to-differential conversion stage. A single
protection card can replace up to N line cards in a N+1
redundancy scheme. Figure 6 shows the MAX4815/
MAX4816/MAX4817 sitting in the line cards where they
can reroute any of the input/output signals to a protection
line card. Figure 7 shows the MAX4815/MAX4816/
MAX4817 sitting in a protection-switching card where the
switches are always powered. These figures do not show
the surge protection elements and resistors for line termi-
nation/impedance matching.
The low on-resistance and high bandwidth of the
MAX4815/MAX4816/MAX4817 yield good pulse tem-
plate and return-loss performance (see the Typical
Operating Characteristics). The pulse template tests for
E1 (twisted pair interface 120
Ω and coaxial interface
75
Ω) and T1 (twisted pair interface 100Ω) were tested
using the Dallas DS2155 single-chip transceiver evalu-
ation board, and twelve switches in parallel with one
switch closed and the other eleven open. The internal
transmit termination feature must be disabled when
using this circuit. To use the same transmit resistors for
E1 twisted pair and coaxial cables, the transmit line
build out control register (TLBC) is set to the value 6Ah.
This sets the driver voltage so the output pulse has the
right amplitude for both 120
Ω (twisted pair) and 75Ω
(coaxial) loads. The analog switches were powered
with dual power supplies at ±5V.
MAX4815/MAX4816/MAX4817
High-Bandwidth, T1/E1, SPST Analog Switches
_______________________________________________________________________________________
9
MAX4815
MAX4816
MAX4817
5V
±10%
LIU
Tx
TRING
TTIP
10V
±10%
1:2
+
-
Vo
RL
NC_
COM_
Figure 1. Fault Protection
相关PDF资料 |
PDF描述 |
|---|---|
| MAX4816ETE+ | IC SWITCH QUAD SPST 16TQFN |
| VI-B0X-IY-F2 | CONVERTER MOD DC/DC 5.2V 50W |
| MAX4818ETE+ | IC SWITCH DUAL SPDT 16TQFN |
| VI-B0W-IY-F2 | CONVERTER MOD DC/DC 5.5V 50W |
| HI6-0201HS-5+ | IC SWITCH QUAD SPST 16SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX4815ETE+ | 功能描述:模拟开关 IC T1/E1 SPST Analog Switch RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| MAX4815ETE+T | 功能描述:模拟开关 IC T1/E1 SPST Analog Switch RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| MAX4815ETE-T | 功能描述:模拟开关 IC RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| MAX4815EUE | 功能描述:模拟开关 IC RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
| MAX4815EUE+ | 功能描述:模拟开关 IC RoHS:否 制造商:Texas Instruments 开关数量:2 开关配置:SPDT 开启电阻（最大值）:0.1 Ohms 切换电压（最大）: 开启时间（最大值）: 关闭时间（最大值）: 工作电源电压:2.7 V to 4.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:DSBGA-16 |
发布紧急采购，3分钟左右您将得到回复。