- 您现在的位置：买卖IC网 > PDF目录385532 > MAX494 (Maxim Integrated Products, Inc.) Quad, Micropower, Single-Supply Rail-to-Rail Op Amps(输入失调电压500μV,单电源满量程运放) PDF资料下载
参数资料
| 型号： | MAX494 |
| 厂商： | Maxim Integrated Products, Inc. |
| 英文描述： | Quad, Micropower, Single-Supply Rail-to-Rail Op Amps(输入失调电压500μV,单电源满量程运放) |
| 中文描述： | 单/双/四路、微功耗、单电源、满摆幅运算放大器 |
| 文件页数： | 13/16页 |
| 文件大小： | 224K |
| 代理商： | MAX494 |
Power-Up S ettling T ime
The MAX492/MAX494/MAX495 have a typical supply
current of 150μA per op amp. Although supply current
is already low, it is sometimes desirable to reduce it fur-
ther by powering down the op amp and associated ICs
for periods of time. For example, when using a MAX494
to buffer the inputs to a multi-channel analog-to-digital
converter (ADC), much of the circuitry could be pow-
ered down between data samples to increase battery
life. If samples are taken infrequently, the op amps,
along with the ADC, may be powered down most of the
time.
When power is reapplied to the MAX492/MAX494/
MAX495, it takes some time for the voltages on the sup-
ply pin and the output pin of the op amp to settle.
Supply settling time depends on the supply voltage, the
value of the bypass capacitor, the output impedance of
the incoming supply, and any lead resistance or induc-
tance between components. Op amp settling time
depends primarily on the output voltage and is slew-rate
limited. With the noninverting input to a voltage follower
held at mid-supply (Figure 9), when the supply steps
from 0V to V
CC
, the output settles in approximately 4μs
for V
CC
= +3V (Figure 10a) or 10μs for V
CC
= +5V
(Figure 10b).
M
S ingle/Dual/Quad, Mic ropower,
S ingle-S upply Rail-to-Rail Op Amps
______________________________________________________________________________________
13
V
50mV/div
V
50mV/div
10
μ
s/div
V
50mV/div
V
50mV/div
10
μ
s/div
MAX495
V
OUT
V
CC
2
3
1k
1k
+5V
7
4
6
Figure 9. Power-Up Test Configuration
Figure 8b. Driving a 10,000pF Capacitive Load with a 47
Isolation Resistor
Figure 8a. Driving a 10,000pF Capacitive Load
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5003 | High-Voltage PWM Power-Supply Controller |
| MAX5003CEE | High-Voltage PWM Power-Supply Controller |
| MAX5003CSE | High-Voltage PWM Power-Supply Controller |
| MAX5003EEE | High-Voltage PWM Power-Supply Controller |
| MAX5003ESE | RES 240-OHM 1% 0.1W 100PPM THICK-FILM SMD-0603 5K/REEL-7IN-PA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX4940ACTN+ | 功能描述:功率驱动器IC Unipolar/Bipolar Digital Pulser RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX4940ACTN+T | 功能描述:功率驱动器IC Unipolar/Bipolar Digital Pulser RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX4940BETN+ | 功能描述:功率驱动器IC Unipolar/Bipolar Digital Pulser RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX4940BETN+T | 功能描述:功率驱动器IC Unipolar/Bipolar Digital Pulser RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MAX4940CTN+ | 功能描述:功率驱动器IC Unipolar/Bipolar Digital Pulser RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。