- 您现在的位置：买卖IC网 > PDF目录3447 > MAX494ESD+ (Maxim Integrated Products)IC OPAMP QD MICROPWR R/R 14SOIC PDF资料下载
参数资料
| 型号： | MAX494ESD+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/17页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP QD MICROPWR R/R 14SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 放大器类型： | 通用 |
| 电路数： | 4 |
| 输出类型： | 满摆幅 |
| 转换速率： | 0.2 V/µs |
| 增益带宽积： | 500kHz |
| 电流 - 输入偏压： | 25nA |
| 电压 - 输入偏移： | 200µV |
| 电流 - 电源： | 150µA |
| 电流 - 输出 / 通道： | 30mA |
| 电压 - 电源，单路/双路(±)： | 2.7 V ~ 6 V，±1.35 V ~ 3 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOIC |
| 包装： | 管件 |
| 产品目录页面： | 1385 (CN2011-ZH PDF) |
MAX492/MAX494/MAX495
Because the MAX492/MAX494/MAX495 have excellent
stability, no isolation resistor is required, except in the
most demanding applications. This is beneficial
because an isolation resistor would degrade the low-
frequency performance of the circuit.
Power-Up Settling Time
The MAX492/MAX494/MAX495 have a typical supply
current of 150A per op amp. Although supply current is
already low, it is sometimes desirable to reduce it further
by powering down the op amp and associated ICs for
periods of time. For example, when using a MAX494 to
buffer the inputs to a multi-channel analog-to-digital con-
verter (ADC), much of the circuitry could be powered
down between data samples to increase battery life. If
samples are taken infrequently, the op amps, along with
the ADC, may be powered down most of the time.
When power is reapplied to the MAX492/MAX494/
MAX495, it takes some time for the voltages on the sup-
ply pin and the output pin of the op amp to settle.
Supply settling time depends on the supply voltage, the
value of the bypass capacitor, the output impedance of
the incoming supply, and any lead resistance or induc-
tance between components. Op amp settling time
depends primarily on the output voltage and is slew-rate
limited. With the noninverting input to a voltage follower
held at mid-supply (Figure 10), when the supply steps
from 0V to VCC, the output settles in approximately 4s
for VCC = +3V (Figure 11a) or 10s for VCC = +5V
(Figure 11b).
Power Supplies and Layout
The MAX492/MAX494/MAX495 operate from a single
2.7V to 6V power supply, or from dual supplies of
±1.35V to ±3V. For single-supply operation, bypass the
power supply with a 1F capacitor in parallel with a
0.1F ceramic capacitor. If operating from dual sup-
plies, bypass each supply to ground.
Good layout improves performance by decreasing the
amount of stray capacitance at the op amp’s inputs and
output. To decrease stray capacitance, minimize both
trace lengths and resistor leads and place external
components close to the op amp’s pins.
Rail-to-Rail Buffers
The
Typical Operating Circuit shows a MAX495 gain-of-
two buffer driving the analog input to a MAX187 12-bit
ADC. Both devices run from a single 5V supply, and the
converter’s internal reference is 4.096V. The MAX495’s
typical input offset voltage is 200V. This results in an
error at the ADC input of 400V, or less than half of one
least significant bit (LSB). Without offset trimming, the
op amp contributes negligible error to the conversion
result.
Single/Dual/Quad, Micropower,
Single-Supply Rail-to-Rail Op Amps
14
______________________________________________________________________________________
VCC
1V/div
VOUT
500mV/div
5
s/div
VCC
2V/div
VOUT
1V/div
5
s/div
Figure 11b. Power-Up Settling Time (VCC = +5V)
Figure 11a. Power-Up Settling Time (VCC = +3V)
相关PDF资料 |
PDF描述 |
|---|---|
| PCF0805R-619KBT1 | RES 619K OHM 0.1W 0805 0.1% SMD |
| MAX494EPD+ | IC OPAMP QUAD MICROPWR R/R 14DIP |
| 2026-35-ALF | GAS DISCHARGE TUBE |
| 77313-801-28 | BERGSTIK HEADER STR |
| MAX407ESA+ | IC OP AMP DUAL SS 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX494ESD+ | 功能描述:运算放大器 - 运放 uPower Single-Supply Rail-Rail RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| MAX494ESD+T | 功能描述:运算放大器 - 运放 uPower Single-Supply Rail-Rail RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| MAX494ESD-T | 功能描述:运算放大器 - 运放 uPower Single-Supply Rail-Rail RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| MAX494MJD | 功能描述:运算放大器 - 运放 RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| MAX4950ACTX+ | 功能描述:均衡器 Single PCIe Re-Driver RoHS:否 制造商:Texas Instruments |
发布紧急采购，3分钟左右您将得到回复。