- 您现在的位置：买卖IC网 > PDF目录1842 > MAX5022EUA+ (Maxim Integrated Products)IC REG CTRLR FLYBK ISO PWM 8UMAX PDF资料下载
参数资料
| 型号： | MAX5022EUA+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 5/11页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR FLYBK ISO PWM 8UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 290kHz |
| 占空比： | 76% |
| 电源电压： | 11 V ~ 28 V |
| 降压： | 无 |
| 升压： | 无 |
| 回扫： | 是 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 包装： | 管件 |
Current-Mode PWM Controllers for Isolated
Power Supplies
Pin Description
PIN
SOT23
1
2
3
4
PDIP
μ MAX
8
7
6
3
NAME
CS
GND
NDRV
V CC
FUNCTION
Current Sense Connection for PWM Regulation and Overcurrent Protection. The current-limit
comparator threshold is internally set to 0.6V.
Power-Supply Ground
External N-Channel MOSFET Gate Connection
Gate Drive Supply. Internally regulated down from V IN . Decouple with a 10nF or larger
capacitor to GND.
IC Supply. Decouple with a 10nF or larger capacitor to GND. Connect a startup resistor
5
2
V IN
(R s ) from the input supply line to V IN . Connect to bias winding through diode rectifier.
See Typical Operating Circuit .
6
—
1
4, 5
OPTO
N.C.
Optocoupler Transistor Collector Connection. Connect emitter of optocoupler to GND.
The OPTO has an internal pullup resistor with a typical value of 6.2k ? .
No Connection. Do not make connections to these pins.
Detailed Description
The MAX5021/MAX5022 are current-mode PWM con-
trollers that have been specifically designed for use in
isolated power supplies. An undervoltage lockout cir-
cuit (UVLO) with a large hysteresis (14V) along with
very low startup and operating current result in high-
efficiency, universal input power supplies. Both devices
can be used in power supplies capable of operating
from a universal 85VAC to 265VAC line or the telecom
voltage range of -36VDC to -72VDC.
Power supplies designed with these devices use a
high-value startup resistor, R S , (series combination of
R 1 and R 2 ) that charges a reservoir capacitor, C2 (see
Figure 1). During this initial period while the voltage is
less than the UVLO start threshold, the IC typically con-
sumes only 50μA of quiescent current. This low startup
current and the large UVLO hysteresis combined with
the use of a ceramic capacitor C2 keeps the power dis-
sipation in R S to less than 1/4W even at the high end of
the universal AC input voltage (265VAC).
The MAX5021/MAX5022 include a cycle-by-cycle cur-
rent limit which turns off the gate drive to the external
MOSFET during an overcurrent condition. If the output
on the secondary side of transformer T1 is shorted, the
tertiary winding voltage will drop below the 10V thresh-
old causing the UVLO circuit to turn off the gate drive to
the external power MOSFET, thus re-initiating the start-
up sequence.
Startup
Figure 2 shows the voltages on V IN and V CC during
startup. Initially, both V IN and V CC are 0V. After the line
voltage is applied, C2 charges through the startup
resistor, R S , to an intermediate voltage at which point
the internal reference and regulator begin charging C3
(see Figure 1). The bias current consumed by the
device during this period is only 50μA; the remaining
input current charges C2 and C3. Charging of C3 stops
when the V CC voltage reaches approximately 9.5V,
while the voltage across C2 continues rising until it
reaches the wakeup level of 24V. Once V IN exceeds
the UVLO threshold, NDRV begins switching the
MOSFET, transferring energy to the secondary and ter-
tiary outputs. If the voltage on the tertiary output builds
to higher than 10V (UVLO lower threshold), then startup
has been accomplished and sustained operation
will commence.
If V IN drops below 10V before startup is complete, then
the IC goes back into UVLO. In this case, increase the
value of C2 and/or use a MOSFET with a lower gate-
charge requirement.
Startup Time Considerations
The V IN bypass capacitor C2 supplies current immediate-
ly after wakeup. The size of C2 will determine the number
of cycles available for startup. Large values for C2 will
increase the startup time, but will also supply more gate
charge, allowing for more cycles after wakeup. If the
value of C2 is too small, V IN will drop below 10V because
_______________________________________________________________________________________
5
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5023LASA+ | IC REG LDO 5V .15A 8-SOIC |
| MAX5026EUT+T | IC REG BOOST ADJ 40MA SOT23-6 |
| MAX5033BASA+T | IC REG BUCK 5V 0.5A 8SOIC |
| MAX5035CASA+T | IC REG BUCK 12V 1A 8SOIC |
| MAX5038EAI33+ | IC REG CTRLR BUCK PWM CM 28-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5022EUA+ | 功能描述:电流型 PWM 控制器 for Isolated Power Supplies RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX5022EUA+T | 功能描述:电流型 PWM 控制器 for Isolated Power Supplies RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX5022EUA-T | 功能描述:电流型 PWM 控制器 for Isolated Power Supplies RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX5022EUT | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX5022EUT+ | 制造商:Maxim Integrated Products 功能描述:CURRENT MODE PWM CNTRLR 250MA 6PIN SOT-23 - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。