- 您现在的位置：买卖IC网 > PDF目录17279 > MAX5051EVKIT (Maxim Integrated Products)EVAL KIT FOR MAX5051 PDF资料下载
参数资料
| 型号： | MAX5051EVKIT |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/21页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT FOR MAX5051 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，隔离 |
| 输出电压： | 3.3V |
| 电流 - 输出： | 15A |
| 输入电压： | 36 ~ 72V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 250kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | MAX5051 |
Parallelable, Clamped Two-Switch
Power-Supply Controller IC
Detailed Description
The MAX5051 controller IC is designed for two-switch
forward converter power-supply topologies. It incorpo-
rates an advanced set of protection features that
makes it uniquely suitable when high reliability and
comprehensive fault protection are required, as in
power supplies intended for telecommunication
equipment. The device operates over a wide 11V to
76V supply range. By using the MAX5051 with a
secondary-side synchronous rectifier circuit, a very
efficient low output voltage and high output-current
power supply can be designed.
In a typical application, the AVIN pin is connected
directly to the input supply. The PVIN pin is connected
to the input supply through a bleed resistor. This is
used to charge up a reservoir capacitor. When the
voltage across this capacitor reaches approximately
24V, then primary switching commences. If the tertiary
winding is able to supply bias to the IC, then self
boot-strapping takes place and operation continues
normally. If the voltage across the reservoir capacitor
connected to PVIN falls below 6.2V, then switching
stops and the capacitor starts charging up again until
the voltage across it reaches 24V.
This device incorporates synchronization circuitry,
enabling the direct paralleling of two devices for higher
output power and lower input ripple current. Using a
single pin, the circuitry synchronizes and shifts the
phase of the second device by 180 ° . To enable simul-
taneous wakeup and shutdown, a STARTUP pin is pro-
vided. Connect all the STARTUP pins of all MAX5051
devices together to facilitate parallel operation in the
primary side. When each power supply generates dif-
ferent output voltages, connecting the STARTUP pins is
not necessary.
Power Topology
The two-switch forward-converter topology offers
outstanding robustness against faults and transformer
saturation while allowing the use of SO-8 power
MOSFETs with a voltage rating equal to only that of the
input supply voltage.
? Clean modulator ramp and higher amplitude for
increased stability;
? Stable operating current of the optocoupler LED and
phototransistor for maximized control-loop band-
width (in current-mode applications, the optocoupler
bias point is output-load dependent);
? Predictable loop dynamics simplifying the design of
the control loop.
The two-switch power topology has the added benefit
of recovering practically all magnetizing as well as the
leakage energy stored in the parasitics of the isolation
transformer. The lower clamped voltages on the prima-
ry power FETs allow for the use of low R DS(ON) devices.
Figure 2 shows the schematic diagram of a 48V input
3.3V/10A output power supply built around the
MAX5051.
MOSFET Drivers
The MAX5051 ’ s integrated high- and low-side MOSFET
drivers source and sink up to 2A of peak currents,
resulting in very low losses even when switching high
gate charge MOSFETs. The high-side gate driver
requires its own bypass capacitor connected between
BST and XFRMRH. Use high-quality ceramic capacitors
close to these two pins for bypass. Under normal oper-
ating conditions, the energy stored in the transformer
parasitics swings the XFRMRH pin to ground while the
transformer is resetting. During this time, the charge on
the boost capacitor connected to the BST pin is replen-
ished. However, under certain conditions, such as
when the magnetizing inductance of the transformer is
very high or when using conventional rectification at the
output, the duty cycle with light loads may become very
small. Thus, the energy stored could be insufficient to
swing XFRMRH to ground and replenish the boost
capacitor. Figure 3 shows the equivalent circuit during
the magnetizing inductance reset interval, assuming
synchronous rectification where the output inductor is
not allowed to run discontinuous.
If the magnetizing inductance is kept below the follow-
ing minimum, then the boost capacitor charge will
not deplete:
+ ( 0 . 005 A )
f s total s f
Qg
Voltage-mode control with feed-forward compensation
allows the rejection of input supply disturbances within
a single cycle, similar to that of current-mode controlled
topologies. This control method offers some significant
L M ≤ 0 . 294 d 2
2
V IN
benefits not possible with current-mode control. These
benefits are:
? No minimum duty-cycle requirement because of cur-
rent-signal blanking;
where d is the duty cycle, V IN is the input voltage, f S is
the switching frequency, and Q gtotal is the total gate
charge for the high-side MOSFET. The above formula is
only an approximation; the actual value will depend on
other parasitics as well.
12
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| 695D155X9050E2T | CAP TANT 1.5UF 50V 10% 2410 |
| FGP50CHE3/73 | DIODE 5A 150V 35NS GP20 AXIAL |
| ASPI-0403S-152M-T | INDUCTOR POWER 1500UH 20% SMD |
| GEM30DTBD | CONN EDGECARD 60POS R/A .156 SLD |
| R1S8-3.324 | CONV DC/DC 1W 3.3VIN 24VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5052 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Current-Mode PWM Controllers with an Error Amplifier for Isolated/Nonisolated Power Supplies |
| MAX5052AEUA | 功能描述:电流型 PWM 控制器 w/Error Amplifier RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX5052AEUA+ | 功能描述:电流型 PWM 控制器 w/Error Amplifier RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX5052AEUA+T | 功能描述:电流型 PWM 控制器 w/Error Amplifier RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。