- 您现在的位置：买卖IC网 > PDF目录15514 > MAX5094BASA+ (Maxim Integrated Products)IC REG CTRLR FLYBK DIV ISO 8SOIC PDF资料下载
参数资料
| 型号： | MAX5094BASA+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 15/22页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR FLYBK DIV ISO 8SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1MHz |
| 占空比： | 50% |
| 电源电压： | 8 V ~ 25 V |
| 降压： | 无 |
| 升压： | 无 |
| 回扫： | 是 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 是 |
| Cuk： | 无 |
| 隔离： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
| 产品目录页面： | 1411 (CN2011-ZH PDF) |
High-Performance, Single-Ended, Current-Mode
PWM Controllers
R CS = CS
R T × C T × 10 3
f OSC =
MAX5095_Feedback
The MAX5095A/MAX5095B/MAX5095C use either an
external error amplifier when designed into a nonisolat-
ed converter or an error amplifier and optocoupler
when designed into an isolated power supply. The
COMP input is level-shifted and connected to the
inverting terminal of the PWM comparator (CPWM).
Connect the COMP input to the output of the external
error amplifier for nonisolated design. Pull COMP high
externally to 5V (or REF) and connect the optocoupler
transistor as shown in Figures 7 and 8. COMP can be
used for soft-start and also as a shutdown. See the
Typical Operating Characteristics to find the turn-off
COMP voltage at different temperatures.
Oscillator
The oscillator frequency is programmed by adding an
external capacitor and resistor at R T /C T (see R T and C T
in the Typical Application Circuits ). R T is connected
from R T /C T to the 5V reference (REF) and C T is con-
nected from R T /C T to GND. REF charges C T through R T
until its voltage reaches 2.8V. C T then discharges
through an 8.3mA internal current sink until C T ’s voltage
reaches 1.1V, at which time C T is allowed to charge
through R T again. The oscillator’s period will be the
sum of the charge and discharge times of C T . Calculate
the charge time as
t C = 0.57 x R T x C T
The discharge time is then
t D =
4 . 88 × R T ? 1 . 8 × 10 3
The oscillator frequency will then be
1
t C + t D
For the MAX5094A/MAX5094C/MAX5095A, the convert-
er output switching frequency (f SW ) is the same as the
oscillator frequency (f OSC ). For the MAX5094B/
MAX5094D/MAX5095B/MAX5095C, the output switch-
ing frequency is 1/2 the oscillator frequency.
Reference Output
REF is a 5V reference output that can source 20mA.
Bypass REF to GND with a 0.1μF capacitor.
Current Limit
The MAX5094/MAX5095 include a fast current-limit com-
parator to terminate the ON cycle during an overload or a
fault condition. The current-sense resistor (R CS ), connect-
ed between the source of the MOSFET and GND, sets
the current limit. The CS input has a voltage trip level
(V CS ) of 1V (MAX5094A/B) or 0.3V (MAX5094C/D,
MAX5095_). Use the following equation to calculate R CS :
V
I P ? P
I P-P is the peak current in the primary that flows through
the MOSFET. When the voltage produced by this current
(through the current-sense resistor) exceeds the current-
limit comparator threshold, the MOSFET driver (OUT) will
turn the switch off within 60ns. In most cases, a small RC
filter is required to filter out the leading-edge spike on the
sense waveform. Set the time constant of the RC filter at
50ns. Use a current transformer to limit the losses in the
current-sense resistor and achieve higher efficiency
especially at low input-voltage operation.
Synchronization (MAX5095A/MAX5095B)
SYNC
SYNC is a bidirectional input/output that outputs a syn-
chronizing pulse and accepts a synchronizing pulse
from other MAX5095A/MAX5095Bs (see Figures 7 and
9). As an output, SYNC is an open-drain p-channel
MOSFET driven from the internal oscillator and requires
an external pulldown resistor (R SYNC ) between 500 ?
and 5k ? . As an input, SYNC accepts the output pulses
from other MAX5095A/MAX5095Bs.
Synchronize multiple MAX5095A/MAX5095Bs by con-
necting their SYNC pins together. All devices connected
together will synchronize to the one operating at the
highest frequency. The rising edge of SYNC will precede
the rising edge of OUT by approximately the discharge
time (t D ) of the oscillator (see the Oscillator section). The
pulse width of the SYNC output is equal to the time
required to discharge the stray capacitance at SYNC
through R SYNC plus the C T discharge time t D . Adjust
R T /C T such that the minimum discharge time t D is 200ns.
______________________________________________________________________________________
15
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1771ESA+ | IC REG CTRLR BST PWM 8-SOIC |
| MAX1744EUB+ | IC REG CTRLR BUCK PWM 10-UMAX |
| MAX1876EEG+ | IC REG CTRLR BUCK PWM VM 24-QSOP |
| MAX1651ESA+ | IC REG CTRLR BUCK PWM 8-SOIC |
| MAX1649ESA+ | IC REG CTRLR BUCK PWM 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5094BASA+ | 功能描述:电流型 PWM 控制器 Single-Ended RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX5094BASA+T | 功能描述:电流型 PWM 控制器 Single-Ended RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX5094BASA-T | 功能描述:电流型 PWM 控制器 Single-Ended RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX5094BAUA | 功能描述:电流型 PWM 控制器 Single-Ended RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。