- 您现在的位置：买卖IC网 > PDF目录17274 > MAX5097AEVKIT+ (Maxim Integrated Products)EVAL KIT FOR MAX5097A PDF资料下载
参数资料
| 型号： | MAX5097AEVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 15/21页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT FOR MAX5097A |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 主要目的： | DC/DC，步降 |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 3.3V |
| 电流 - 输出： | 600mA |
| 输入电压： | 5 ~ 40 V |
| 稳压器拓扑结构： | 降压 |
| 频率 - 开关： | 330kHz |
| 板类型： | 完全填充 |
| 已供物品： | 板 |
| 已用 IC / 零件： | MAX5097A |
40V, 600mA Buck Converters with Low-
Quiescent-Current Linear Regulator Mode
ripple is mainly composed of Δ V Q (caused by the
capacitor discharge) and Δ V ESR (caused by the volt-
age drop across the ESR of the output capacitor).
Normally, a good approximation of the output voltage
ripple is Δ V RIPPLE ≈ Δ V ESR + Δ V Q . If using ceramic
capacitors, assume the contribution to the output volt-
age ripple from the ESR and the capacitor discharge to
be equal to 20% and 80%, respectively. If using alu-
minum electrolyte capacitors, assume the contribution
to the output voltage ripple from the ESR and the
capacitor discharge to be equal to 90% and 10%,
respectively.
Use the following equations for calculating the output
capacitance and its ESR for required peak-to-peak out-
put voltage ripple.
where I STEP is the load step, t STEP is the rise time of the
load step, and t RESPONSE is the response time of the
controller. The response time of the converter is
approximately one third of the inverse of its closed-loop
bandwidth and also depends on the phase margin.
Rectifier Selection
The MAX5096/MAX5097 require an external Schottky/
fast-recovery diode rectifier as a freewheeling diode.
Connect this rectifier close to the device using short
leads and short PC board traces. Choose a rectifier
with a continuous current rating greater than the high-
est output current-limit threshold (1.9A) and with a volt-
age rating greater than the maximum expected input
voltage, V IN . Use a low forward-voltage-drop Schottky
rectifier to limit the negative voltage at LX. Avoid higher
C OUT =
Δ I P ? P
16 × Δ V Q × f SW
than necessary reverse-voltage Schottky rectifiers that
have higher forward-voltage drops. Use a 60V (max)
Schottky rectifier with a 2A current rating. The Schottky
ESR =
Δ V ESR
Δ I P ? P
rectifier leakage current at high temperature significant-
ly increases the quiescent current in LDO Mode. In
applications where LDO Mode quiescent current is
Δ I P-P is the peak-to-peak inductor current and f SW is
the converter’s switching frequency.
The allowable deviation of the output voltage during
fast load transients also determines the output capaci-
tance, its ESR, and its equivalent series inductance
(ESL). The output capacitor supplies the load current
during a load step until the controller responds with a
greater duty cycle. The response time (t RESPONSE )
depends on the closed-loop bandwidth of the converter
(see the Compensation Network section). The resistive
drop across the output capacitor ’s ESR, the drop
across the capacitor ’s ESL, and the capacitor dis-
charge, causes a voltage drop during the load step.
Use a combination of low-ESR tantalum/aluminum elec-
trolytic and ceramic capacitors for better transient load
important, use an ultra-fast switching diode to limit the
leakage current. In this type of application, use
MURS105, MURS120 for their fast-switching and low-
leakage features.
Input Capacitor Selection
The discontinuous input current of the buck converter
causes large input ripple currents and therefore, the
input capacitor must be carefully chosen to keep the
input voltage ripple within design requirements. The
input voltage ripple is comprised of Δ V Q (caused by
the capacitor discharge) and Δ V ESR (caused by the
ESR of the input capacitor). The total voltage ripple is
the sum of Δ V Q and Δ V ESR . Calculate the input capaci-
tance and ESR required for a specified ripple using the
following equations (continuous mode):
? I OUT _ MAX +
Δ I P ? P ?
?
?
and voltage ripple performance. Non-leaded capaci-
tors and/or multiple parallel capacitors help reduce the
ESL. Keep the maximum output voltage deviation
below the tolerable limits of the electronics being pow-
ESR =
?
?
Δ V ESR
2
ered. Use the following equations to calculate the
required ESR, ESL, and capacitance value during a
load step:
C IN =
I OUT _ MAX × D ( 1 ? D )
Δ V Q × f SW
Δ V ESR
C OUT = STEP RESPONSE
Δ V ESL × t STEP
Δ I P ? P =
( V IN ? V OUT ) × V OUT
D = OUT
ESR =
ESL =
Δ I STEP
I × t
Δ V Q
I STEP
where
and
V IN × f SW × L
V
V IN
I OUT_MAX is the maximum output current and D is the
duty cycle.
______________________________________________________________________________________
15
相关PDF资料 |
PDF描述 |
|---|---|
| CBC2518T101K | INDUCTOR 100UH 10% 1007 SMD |
| TH3E686K020C0600 | CAP TANT 68UF 20V 10% 2917 |
| AS5040 DB V2 | BOARD DEMO AS5040 |
| EEC22DREI | CONN EDGECARD 44POS .100 EYELET |
| MAX15035EVKIT+ | EVALUATION KIT FOR MAX15035 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5097AEVKIT+ | 功能描述:电源管理IC开发工具 MAX5097A Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX5097B | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:40V, 600mA Buck Converters with Low-Quiescent-Current Linear Regulator Mode |
| MAX5097BATE/V+ | 功能描述:直流/直流开关转换器 40V 600mA Buck Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX5097BATE/V+T | 功能描述:直流/直流开关转换器 40V 600mA Buck Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX5097BATE+ | 功能描述:直流/直流开关转换器 40V 600mA Buck Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。