- 您现在的位置：买卖IC网 > PDF目录3276 > MAX5165LCCM+ (Maxim Integrated Products)IC AMP SAMPLE/HOLD 32CH 48-LQFP PDF资料下载
参数资料
| 型号： | MAX5165LCCM+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC AMP SAMPLE/HOLD 32CH 48-LQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 250 |
| 放大器类型： | 采样和保持 |
| 电路数： | 32 |
| 电流 - 输入偏压： | 1µA |
| 电压 - 输入偏移： | 5000µV |
| 电流 - 电源： | 36mA |
| 电流 - 输出 / 通道： | 2mA |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP（7x7） |
| 包装： | 托盘 |
Sample Mode
Driving M3–M0 low (one at a time) selects sample
mode (Tables 1, 2). During sample mode, the selected
multiplexer channel connects to IN, allowing the hold
capacitor to acquire the input signal. To guarantee an
accurate sample, maintain sample mode for at least
4s. The output of the S/H amplifier tracks the input
after 4s. Only the addressed channel on the selected
multiplexer samples the input; all other channels remain
in hold mode.
Hold Mode
Driving M3–M0 high selects hold mode. Hold mode dis-
ables the multiplexer and disconnects all eight chan-
nels on the 1-to-8 multiplexer from the input. When a
channel is disconnected, the hold capacitor maintains
the sampled voltage at the output with a 1mV/sec
droop rate (towards VDD).
Hold Step
When switching between sample mode and hold mode,
the voltage of the hold capacitor changes due to
charge injection from stray capacitance. This voltage
change, called hold step, is minimized by limiting the
amount of stray capacitance seen by the hold capaci-
tor. The MAX5165 limits the hold step to 0.25mV (typ).
An output capacitor to ground can be used to filter out
this small hold-step error.
Output
The MAX5165 contains an output buffer for each multi-
plexer channel (32 total), so the hold capacitor sees a
high-impedance input, reducing the droop rate. The
capacitor droops at a 1mV/sec (typ) rate while in hold
mode. The buffer also provides a low output imped-
ance; however, the device contains output resistors in
series with the buffer output (Figure 1) for selected out-
put filtering. To provide greater design flexibility, the
MAX5165 is available with an RO of 50
, 500, or 1k.
Note: Output loads increase the analog supply cur-
rent (IDD and ISS). Excessive loading of the output(s)
damages the device by consuming more power than the
device will dissipate (see Absolute Maximum Ratings).
The resistor-divider formed by the output resistor (ROUT)
and load impedance (RL) scales the sampled voltage
(VSAMP). Determine the output voltage (VOUT_) as follows:
Voltage Gain = AV = RL / (RL + ROUT)
VOUT_ = VSAMP AV
The maximum output voltage range depends on the
analog supply voltages available, and the scaling factor
used:
(VSS + 0.75V) AV
≤ VOUT_ ≤ (VDD - 2.4V) AV
when RL =
∞, then AV = 1 and this equation becomes:
(VSS + 0.75V)
≤ VOUT ≤ (VDD - 2.4V)
MAX5165
32-Channel Sample/Hold Amplifier
with a Single Multiplexed Input
_______________________________________________________________________________________
7
0
Table 1. Output Selection
Table 2. Mode Selection
0
1
0
1
0
1
ADDRESS
0
1
0
1
OUT2
OUT3
OUT6
OUT0
OUT7
OUT1
OUT4
OUT5
OUT10
OUT11
OUT14
OUT8
OUT15
OUT9
OUT12
OUT13
OUT18
OUT19
OUT22
OUT16
OUT23
OUT17
OUT20
OUT21
OUTPUT SELECTED
OUT26
OUT27
OUT30
OUT24
OUT31
OUT25
OUT28
OUT29
A2
A1
A0
MUX0
MUX1
MUX2
MUX3
0 = Logic Low, 1 = Logic High
0
1
Sample mode enabled on selected
analog multiplexer and channel
(Table 1).
Hold mode enabled on selected
analog multiplexer and channel
(Table 1).
MODE-SELECT
INPUTS (M3–M0)
ACTION
0 = Logic Low, 1 = Logic High
* Only one M_ input asserted low; all others must be logic high
to meet the timing specification (see Single vs. Simultaneous
Sampling section).
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5166LECM+ | IC AMP SAMPLE/HOLD 32CH 48-LQFP |
| MAX5165MCCM+ | IC AMP SAMPLE/HOLD 32CH 48-LQFP |
| MAX5165LECM+ | IC AMP SAMPLE/HOLD 32CH 48-LQFP |
| MAX5165NCCM+ | IC AMP SAMPLE/HOLD 32CH 48-LQFP |
| MAX5165NECM+ | IC AMP SAMPLE/HOLD 32CH 48-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5165LCCM+ | 功能描述:采样&保持放大器 32Ch Sample/Hold Amp RoHS:否 制造商:Texas Instruments 通道数量:2 捕获时间:20 us 电源电压-最大:18 V 最大工作温度:+ 85 C 最小工作温度:- 25 C 安装风格: 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5165LCCM+T | 功能描述:采样&保持放大器 32Ch Sample/Hold Amp RoHS:否 制造商:Texas Instruments 通道数量:2 捕获时间:20 us 电源电压-最大:18 V 最大工作温度:+ 85 C 最小工作温度:- 25 C 安装风格: 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5165LCCM-T | 功能描述:采样&保持放大器 RoHS:否 制造商:Texas Instruments 通道数量:2 捕获时间:20 us 电源电压-最大:18 V 最大工作温度:+ 85 C 最小工作温度:- 25 C 安装风格: 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5165LECM | 功能描述:采样&保持放大器 RoHS:否 制造商:Texas Instruments 通道数量:2 捕获时间:20 us 电源电压-最大:18 V 最大工作温度:+ 85 C 最小工作温度:- 25 C 安装风格: 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5165LECM+ | 功能描述:采样&保持放大器 32Ch Sample/Hold Amp RoHS:否 制造商:Texas Instruments 通道数量:2 捕获时间:20 us 电源电压-最大:18 V 最大工作温度:+ 85 C 最小工作温度:- 25 C 安装风格: 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。