- 您现在的位置：买卖IC网 > PDF目录8862 > MAX532AEWE+ (Maxim Integrated Products)IC MDAC 12BIT DUAL SER 16-SOIC PDF资料下载
参数资料
| 型号： | MAX532AEWE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 16/16页 |
| 文件大小： | 0K |
| 描述： | IC MDAC 12BIT DUAL SER 16-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 46 |
| 设置时间： | 2.5µs |
| 位数： | 12 |
| 数据接口： | 串行 |
| 转换器数目： | 2 |
| 电压电源： | 双 ± |
| 功率耗散（最大）： | 762mW |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 管件 |
| 输出数目和类型： | 2 电压，单极；2 电压，双极 |
| 采样率（每秒）： | * |
| 产品目录页面： | 1394 (CN2011-ZH PDF) |
MAX532
Dual, Serial-Input,
Voltage-Output, 12-Bit MDAC
_______________________________________________________________________________________
9
Figure 4. Connections for Microwire
SCLK
DIN
DOUT
CS
LDAC
SK
SO
SI
I/O
MAX532
MICROWIRE
PORT
5V
1k
THE DOUT-SI CONNECTION IS NOT REQUIRED FOR WRITING TO THE
MAX532, BUT MAY BE USED FOR READ-BACK PURPOSES.
Figure 5. Connections for SPI
DOUT
DIN
SCLK
CS
LDAC
MISO
MOSI
SCK
I/O
MAX532
SPI
PORT
SS
5V
CPOL = 0,CPHA = 0
1k
THE DOUT-MISO CONNECTION IS NOT REQUIRED FOR WRITING TO THE MAX532,
BUT MAY BE USED FOR READ-BACK PURPOSES.
_______________Detailed Description
Digital Interface
The MAX532 is Microwire and SPI compatible (Figures
4 and 5). Both DACs are programmed by writing three
8-bit words (see Figures 2 and 3, and the
Functional
Diagram). Serial data is clocked into the data registers
MSB first, with DACB information preceding DACA
information. Data is clocked in on the rising edge of
SCLK while
CS is low. With CS high, data can not be
clocked into DIN, and DOUT is high impedance. SCLK
can be driven at rates up to 6.25MHz.
The MAX532 uses either a 3-wire or a 4-wire serial
interface. Three wires may be used (
CS, DIN, SCLK)
by tying
LDAC low. With LDAC low, the DACs are
updated simultaneously when
CS goes high (see
Figure 2 and the
Functional Diagram). The 3-wire inter-
face may be used if the MAX532 is used alone, or if two
or more MAX532s are cascaded (DOUT of one device
tied to DIN of the other) (Figure 6).
The 4-wire interface (
LDAC, CS, DIN, SCLK) is required
if several serial devices are tied to the same data line,
and it is desirable to update them simultaneously
(Figure 7). With the 4-wire interface, the DACs are
updated when
LDAC goes low (see Figure 3 and the
Functional Diagram).
A serial output, DOUT, allows cascading of two or more
MAX532s and allows read-back of the data written to
the device’s 24-bit shift register. The data at DOUT is
delayed 24 clock cycles from the data at DIN (see
Figures 2 and 3, and the
Functional Diagram). DOUT
is an open-drain N-channel MOSFET that requires an
external pull-up resistor (typically 1k
if pulled up to
+5V, and 3k
if pulled up to +12V or +15V). Logic lev-
els are guaranteed with sink currents up to 5mA (see
Electrical Characteristics). Output data changes on the
falling edge of SCLK when
CS is low. If CS is high,
DOUT is three-state (high-impedance).
Daisy-Chaining Devices
Any number of MAX532s can be daisy-chained by con-
necting the DOUT pin of one device (with a pull-up
resistor) to the DIN pin of the following device in the
chain (Figure 6).
When daisy-chaining devices, tCSS0 (CS low to SCLK
high), must be the greater of tDV + tDS or tDS + (tRC + tTR
- tCS), where tCSW is the CS pulse width used in the sys-
tem and the term (tRC + tTR - tCSW) accounts for the time
spent charging the DOUT capacitance with the external
pull-up resistor. So, for tRC < 250ns, tCSS0 is simply tDV
+ tDS. Calculate tRC using the following equation:
tRC = RP x C x ln (VPULL-UP/(VPULL-UP - 2.4V))
where VPULL-UP is the voltage that the pull-up resistor
is connected to, RP is the value of the pull-up resistor,
and C is the capacitance at DOUT. Values of tRC are
given in Table 1.
相关PDF资料 |
PDF描述 |
|---|---|
| ICS507M-01I | IC CLOCK SYNTHESIZER PECL 16SOIC |
| ICS507M-01 | IC CLOCK SYNTHESIZER PECL 16SOIC |
| MS27473T24F61B | CONN HSG PLUG 61POS STRGHT SCKT |
| ICS503M | IC PLL CLK MULTIPLIER 8-SOIC |
| MS27656T17B8SLC | CONN HSG RCPT 8POS WALL MT SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX532AEWE/GH9-T | 制造商:Maxim Integrated Products 功能描述:DUAL, SERIAL INPUT, VOLTAGE-OUTPUT, MULTIPLYING, 12-BIT DAC - Tape and Reel |
| MAX532AEWE+ | 功能描述:数模转换器- DAC 12-Bit 2Ch Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX532AEWE+T | 功能描述:数模转换器- DAC 12-Bit 2Ch Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX532AEWE-C40276 | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX532AEWE-T | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。