- 您现在的位置：买卖IC网 > PDF目录4573 > MAX5426BEUD+ (Maxim Integrated Products)IC INSTR AMP PROGR PREC 14-TSSOP PDF资料下载
参数资料
| 型号： | MAX5426BEUD+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/9页 |
| 文件大小： | 0K |
| 描述： | IC INSTR AMP PROGR PREC 14-TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 96 |
| 系列： | * |
| 类型： | * |
| 应用： | * |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 管件 |
MAX5426
Precision Resistor Network for
Programmable Instrumentation Amplifiers
6
_______________________________________________________________________________________
Applications Information
The MAX5426 is ideal for programmable instrumentation
amplifier applications. The typical application circuit of
Figure 1 uses the MAX5426 in classical instrumentation
amplifier configurations. Two digital inputs set the gain to
1, 2, 4, or 8.
Op Amp Selection Guidelines
Selection of an op amp for instrumentation amplifier cir-
cuits depends on the accuracy requirements of the
specific application. General guidelines are to choose
an op amp with sufficient open-loop gain, low input-off-
set voltage, and a high common-mode rejection ratio.
High open-loop gain is needed to increase the gain
accuracy, while low input-offset voltage and low input-
offset current help meet gain and offset requirements.
Other parameters such as low input capacitance, low
input bias current, high input common-mode range,
and low noise often need to be considered for a wide
input voltage range stability and AC considerations.
The MAX427 is an excellent choice to use with the
MAX5426.
Stereo Audio-Taper Attenuator
Figure 2 shows the application of the MAX5426 as a dual
attenuator that can be used in stereo audio systems.
Power Supplies and Bypassing
The MAX5426 operates from dual ±5V to ±15V sup-
plies. In many applications the MAX5426 does not
require bypassing. If power-supply noise is excessive,
bypass VDD and VSS with 0.1F ceramic capacitors to
GND.
Layout Concerns
For best performance, reduce parasitic board capaci-
tance by minimizing the circuit board trace from ampli-
fier outputs to inverting inputs. Also choose op amps
with low input capacitance.
CM
FB2
INDIF-
OUT2
INDIF+
OUT
OFFSET
VDD
VIN-
VIN+
GND
D1
D0
FB1
OUT1
VSS
VOUT
MAX5426
MAX427
Figure 1. Programmable Instrumentation Amplifier Using MAX5426
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5426AEUD+T | IC INSTR AMP PROGR PREC 14-TSSOP |
| MAX4507EAP+T | IC SIGNAL LINE PROTECTOR 20-SSOP |
| MAX5426BEUD+T | IC INSTR AMP PROGR PREC 14-TSSOP |
| TLE8264-2E | IC SYSTEM BASIS CHIP DSO-36 |
| MAX4507CAP+T | IC SIGNAL LINE PROTECTOR 20-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5426BEUD+ | 功能描述:仪表放大器 Prec Resistor Net for Prog Inst Amp RoHS:否 制造商:Texas Instruments 通道数量: 输入补偿电压:150 V 可用增益调整: 最大输入电阻:10 kOhms 共模抑制比（最小值）:88 dB 工作电源电压:2.7 V to 36 V 电源电流:200 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:MSOP-8 封装:Bulk |
| MAX5426BEUD+T | 功能描述:仪表放大器 Prec Resistor Net for Prog Inst Amp RoHS:否 制造商:Texas Instruments 通道数量: 输入补偿电压:150 V 可用增益调整: 最大输入电阻:10 kOhms 共模抑制比（最小值）:88 dB 工作电源电压:2.7 V to 36 V 电源电流:200 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:MSOP-8 封装:Bulk |
| MAX5426BEUD-T | 功能描述:特殊用途放大器 RoHS:否 制造商:Texas Instruments 通道数量:Single 共模抑制比（最小值）: 输入补偿电压: 工作电源电压:3 V to 5.5 V 电源电流:5 mA 最大功率耗散: 最大工作温度:+ 70 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-20 封装:Reel |
| MAX5426CEUD | 功能描述:特殊用途放大器 RoHS:否 制造商:Texas Instruments 通道数量:Single 共模抑制比（最小值）: 输入补偿电压: 工作电源电压:3 V to 5.5 V 电源电流:5 mA 最大功率耗散: 最大工作温度:+ 70 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:QFN-20 封装:Reel |
| MAX5426CEUD+ | 功能描述:仪表放大器 Prec Resistor Net for Prog Inst Amp RoHS:否 制造商:Texas Instruments 通道数量: 输入补偿电压:150 V 可用增益调整: 最大输入电阻:10 kOhms 共模抑制比（最小值）:88 dB 工作电源电压:2.7 V to 36 V 电源电流:200 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:MSOP-8 封装:Bulk |
发布紧急采购，3分钟左右您将得到回复。