- 您现在的位置：买卖IC网 > PDF目录9188 > MAX5432META+T (Maxim Integrated Products)IC POT DGTL 32-TAP NV I2C 8-TDFN PDF资料下载
参数资料
| 型号： | MAX5432META+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 18/19页 |
| 文件大小： | 0K |
| 描述： | IC POT DGTL 32-TAP NV I2C 8-TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 接片： | 32 |
| 电阻（欧姆）： | 50k |
| 电路数： | 1 |
| 温度系数： | 标准值 35 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 2.7 V ~ 5.25 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WDFN 裸露焊盘 |
| 供应商设备封装： | 8-TDFN-EP（3x3） |
| 包装： | 带卷 (TR) |
MAX5432–MAX5435
32-Tap, Nonvolatile, I2C, Linear, Digital
Potentiometers
8
_______________________________________________________________________________________
Detailed Description
The MAX5432–MAX5435 contain a resistor array with
31 resistive elements. The MAX5432/MAX5434 provide
a total end-to-end resistance of 50k
, and the
MAX5433/MAX5435 provide an end-to-end resistance
of 100k
.
The MAX5432/MAX5433 allow access to the high, low,
and wiper terminals for a standard voltage-divider con-
figuration. Connect H, L, and W in any desired configu-
ration as long as their voltages fall between GND and
VDD. The MAX5434/MAX5435 are variable resistors
with H internally connected to the wiper.
A simple 2-wire I2C-compatible serial interface moves
the wiper among the 32 tap points. Eight data bits, an
address byte, and a control byte program the wiper
position. A nonvolatile memory stores and recalls the
wiper position in the nonvolatile memory upon power-up.
The nonvolatile memory is guaranteed for 200,000 wiper
store cycles and 50 years for wiper data retention.
Digital Interface
The MAX5432–MAX5435 feature an internal, nonvolatile
EEPROM that returns the wiper to its previously stored
position at power-up. The shift register decodes the
control and address bits, routing the data to the proper
memory registers. Write data to the volatile memory
register to immediately update the wiper position, or
write data to the nonvolatile register for storage. Writing
to the nonvolatile register takes a minimum of 12ms.
The volatile register retains data as long as the device
is enabled and powered. Removing power clears the
volatile register. The nonvolatile register retains data
even after power is removed. Upon power-up, the
power-on reset circuitry and internal oscillator control
the transfer of data from the nonvolatile register to the
volatile register.
Serial Addressing
The MAX5432–MAX5435 operate as a slave that sends
and receives data through an I2C- and SMBus-com-
patible 2-wire interface. The interface uses a serial data
access (SDA) line and a serial clock line (SCL) to
achieve bidirectional communication between
master(s) and slave(s). A master, typically a microcon-
troller, initiates all data transfers to and from the
MAX5432–MAX5435, and generates the SCL clock that
synchronizes the data transfer (Figure 1).
SDA operates as both an input and an open-drain out-
put. SDA requires a pullup resistor, typically 4.7k
.
SCL only operates as an input. SCL requires a pullup
resistor (4.7k
typ) if there are multiple masters on the
2-wire interface, or if the master in a single-master sys-
tem has an open-drain SCL output.
Each transmission consists of a START (S) condition
(Figure 3) sent by a master, followed by the
MAX5432–MAX5435 7-bit slave address plus the 8th bit
(Figure 4), 1 command byte (Figure 7) and 1 data byte,
and finally a STOP (P) condition (Figure 3).
Start and Stop Conditions
Both SCL and SDA remain high when the interface is
not busy. A master signals the beginning of a transmis-
sion with a START (S) condition by transitioning SDA
from high to low while SCL is high. When the master
has finished communicating with the slave, it issues a
STOP (P) condition by transitioning the SDA from low to
Pin Description
PIN
TDFN
THIN SOT23
NAME
FUNCTION
1
—
H
High Terminal
2
4
SDA
I2C-Compatible Interface Data Input
3
2
GND
Ground
4
3
SCL
I2C-Compatible Interface Clock Input
51
VDD
Power-Supply Input. Bypass with a 0.1F capacitor from VDD to GND.
6
—
A0
Address Input. Sets the I2C address. Connect to VDD or GND. Do not leave A0 floating.
7
6
L
Low Terminal
8
5
W
Wiper Terminal
EP
—
EP
Exposed Pad. Internally connected to GND.
SMBus is a trademark of Intel Corporation.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5160LEUA+T | IC POT DGTL LO PWR 32 TAP 8-UMAX |
| MAX5160MEUA+T | IC POT DGTL LO PWR 32 TAP 8-UMAX |
| VI-24X-MW | CONVERTER MOD DC/DC 5.2V 100W |
| X9408WV24Z-2.7 | IC XDCP QUAD 64-TAP 10K 24-TSSOP |
| VI-2WY-MW-F2 | CONVERTER MOD DC/DC 3.3V 66W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5433LETA | 制造商:Maxim Integrated Products 功能描述:32-TAP NONVOLATILE I2C LINEAR D - Rail/Tube |
| MAX5433LETA+ | 制造商:Maxim Integrated Products 功能描述:DGTL POTENTIOMETER 32POS 100KOHM SGL 8TDFN EP - Rail/Tube |
| MAX5433LETA+T | 功能描述:数字电位计 IC 32-Tap Nonvolatile I2C Linear RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| MAX5433LETA-T | 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| MAX5433META | 制造商:Maxim Integrated Products 功能描述:32-TAP NONVOLATILE I2C LINEAR D - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。