- 您现在的位置：买卖IC网 > PDF目录1944 > MAX5475EKA+T (Maxim Integrated Products)IC POT DGTL 32TAP NV SOT23-8 PDF资料下载
参数资料
| 型号： | MAX5475EKA+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC POT DGTL 32TAP NV SOT23-8 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 接片： | 32 |
| 电阻（欧姆）： | 100k |
| 电路数： | 1 |
| 温度系数： | 标准值 35 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | 3 线串行（芯片选择，递增，增/减） |
| 电源电压： | 2.7 V ~ 5.25 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-8 |
| 供应商设备封装： | SOT-23-8 |
| 包装： | 标准包装 |
| 产品目录页面： | 1399 (CN2011-ZH PDF) |
| 其它名称： | MAX5475EKA+TDKR |
MAX5471/MAX5472/MAX5474/MAX5475
32-Tap, Nonvolatile, Linear-Taper Digital
Potentiometers in SOT23
_______________________________________________________________________________________
7
Detailed Description
The MAX5471/MAX5472/MAX5474/MAX5475 contain a
resistor array with 31 resistive elements (Figures 2 and
3). The MAX5471/MAX5474 have a total end-to-end
resistance of 50k
Ω, and the MAX5472/MAX5475 have
an end-to-end resistance of 100k
Ω. The MAX5471/
MAX5472 wiper is connected to the high terminal, and
the low terminal is internally connected to ground, mak-
ing the device a variable resistor. The MAX5474/
MAX5475 allow access to the high, low, and wiper ter-
minals for a standard voltage-divider configuration.
The wiper is moved among the 32 tap points through a
simple 3-wire interface. Nonvolatile memory allows the
wiper position to be stored and recalled to the same
point upon power-up.
Digital Interface
Logic inputs CS, U/D, and INC control the wiper posi-
tion and store it in nonvolatile memory (see the Truth
Table). The chip-select (CS) input enables the serial
interface when low and disables the interface when
high. The position of the wiper is stored when CS transi-
tions from low to high and INC is high (see the Storing
Wiper Position section).
With the serial interface active (CS low), a high-to-low
(falling edge) transition on INC moves the wiper posi-
tion by one resistive element in the direction deter-
mined by the state of U/D. If U/D is high, the wiper
increments and it increases the resistance between W
and L (it decreases the resistance between H and W).
If U/D is low, the wiper decrements and it decreases
the resistance between W and L (it increases the resis-
tance between H and W). The direction of the wiper
(state of U/D) can be changed at any time as long as
the setup and hold times are met.
Since the MAX5471/MAX5472 have the wiper internally
connected to H, an increment command increases the
resistance between H and GND, and a decrement com-
mand decreases the resistance between H and GND.
The wiper performs a make-before-break transition,
ensuring that there is never an open circuit during a
transition from one resistor tap to another. When the
wiper is at either end of the resistor array (max/min),
additional transitions in the direction of the endpoint do
not change the counter value (the wiper does not wrap
around).
Storing Wiper Position
The position of the wiper is stored in nonvolatile memo-
ry whenever CS transitions low-to-high (rising edge)
while INC is high. Upon power-up, the wiper returns to
this stored position. By keeping INC low while taking
CS high, the serial interface can be disabled and the
potentiometer placed in standby without storing the lat-
est wiper position. The factory-default wiper position
is midscale.
These devices can also be operated like a one-time
programmable (OTP) device. Once the desired wiper
position is trimmed and stored in nonvolatile memory,
disable the serial interface by connecting CS to VDD,
and INC to GND. The disabled interface places the
device in standby and disallows any changes to the
wiper position. In OTP mode, these devices become a
fixed 3-terminal potentiometer or a 1-terminal resistor to
GND with less than 1A of supply current.
CS
VW
INC
tCYC
tCI
tIL
tIH
tID
tDI
tIW
tIC
tCPH
WIPER POSITION
STORED
WIPER POSITION
NOT STORED
tIK
NOTE: VW IS NOT A DIGITAL SIGNAL. IT REPRESENTS A WIPER TRANSITION.
tWSC
U/D
Figure 1. Digital Interface and Timing Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5478ETE#TG16 | IC POT DGTL DUAL 256-TAP 16-TQFN |
| MAX5482EUD+ | IC DGTL POT 10BIT NV 14-TSSOP |
| MAX5487ETE#TG16 | IC POT DGTL DUAL 256-TAP 16-TQFN |
| MAX5499ETE+ | IC DIG POT 10BIT 16-TQFN-EP |
| MAX5528GUA+T | IC POT DGTL 1TIME PROGR 8-UMAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5477ETE | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX5477ETE#G16 | 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| MAX5477ETE#TG16 | 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| MAX5477ETE+ | 功能描述:数字电位计 IC Dual 256-Tap NV I2C-Interface RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| MAX5477ETE+T | 功能描述:数字电位计 IC Dual 256-Tap NV I2C-Interface RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。