- 您现在的位置：买卖IC网 > PDF目录9179 > MAX5478EUD+T (Maxim Integrated Products)IC POT DGTL DUAL 256-TAP 14TSSOP PDF资料下载
参数资料
| 型号： | MAX5478EUD+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | IC POT DGTL DUAL 256-TAP 14TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 接片： | 256 |
| 电阻（欧姆）： | 50k |
| 电路数： | 2 |
| 温度系数： | 标准值 70 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 2.7 V ~ 5.25 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 带卷 (TR) |
MAX5477/MAX5478/MAX5479
Dual, 256-Tap, Nonvolatile, I2C-Interface,
Digital Potentiometers
4
_______________________________________________________________________________________
Note 2:
All devices are production tested at TA = +25°C and are guaranteed by design and characterization for -40°C < TA < +85°C.
Note 3:
The DNL and INL are measured with the potentiometer configured as a voltage-divider with H_ = VDD and L_ = GND. The
wiper terminal is unloaded and measured with a high-input-impedance voltmeter.
Note 4:
The DNL and INL are measured with the potentiometer configured as a variable resistor. H_ is unconnected and L_ =
GND. For VDD = +5V, the wiper is driven with 400A (MAX5477), 80A (MAX5478), or 40A (MAX5479). For VDD = +3V,
the wiper is driven with 200A (MAX5477), 40A (MAX5478), or 20A (MAX5479).
Note 5:
The wiper resistance is measured using the source currents given in Note 3.
Note 6:
The devices draw current in excess of the specified supply current when the digital inputs are driven with voltages between
(VDD - 0.5V) and (GND + 0.5V). See Supply Current vs. Digital Input Voltage in the Typical Operating Characteristics.
Note 7:
Wiper at midscale with a 10pF load (DC measurement). L_ = GND, an AC source is applied to H_, and the W_ output is
measured. A 3dB bandwidth occurs when the AC W_/H_ value is 3dB lower than the DC W_/H_ value.
Note 8:
The programming current exists only during power-up and EEPROM writes.
Note 9:
The SCL clock period includes rise and fall times (tR = tF). All digital input signals are specified with tR = tF = 2ns and
timed from a voltage level of (VIL + VIH) / 2.
Note 10: Digital timing is guaranteed by design and characterization, and is not production tested.
Note 11: This is measured from the STOP pulse to the time it takes the output to reach 50% of the output step size (divider mode). It
is measured with a maximum external capacitive load of 10pF.
Note 12: An appropriate bus pullup resistance must be selected depending on board capacitance. Refer to the I
2C-bus specifica-
tion document linked to this web address: www.semiconductors.philips.com/acrobat/literature/9398/39340011.pdf
Note 13: The idle time begins from the initiation of the STOP pulse.
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
ANALOG SECTION
MAX5477
325
MAX5478
500
Wiper Settling Time (Note 11)
tWS
MAX5479
1000
ns
DIGITAL SECTION
SCL Clock Frequency
fSCL
400
kHz
Setup Time for START Condition
tSU:STA
0.6
s
Hold Time for START Condition
tHD:STA
0.6
s
SCL High Time
tHIGH
0.6
s
SCL Low Time
tLOW
1.3
s
Data Setup Time
tSU:DAT
100
ns
Data Hold Time
tHD:DAT
0
0.9
s
SDA, SCL Rise Time
tR
300
ns
SDA, SCL Fall Time
tF
300
ns
Setup Time for STOP Condition
tSU:STO
0.6
s
Bus Free Time Between STOP and
START Condition
tBUF
Minimum power-up rate = 0.2V/s
1.3
s
Pulse Width of Spike Suppressed
tSP
50
ns
Capacitive Load for Each Bus Line
CB
(Note 12)
400
pF
Write NV Register Busy Time
(Note 13)
12
ms
TIMING CHARACTERISTICS
(VDD = +2.7V to +5.25V, H_ = VDD, L_ = GND, TA = -40°C to +85°C, unless otherwise noted. Typical values are at VDD = +5V,
TA = +25°C. See Figure 1.) (Notes 9 and 10)
相关PDF资料 |
PDF描述 |
|---|---|
| VE-2WT-MY-F1 | CONVERTER MOD DC/DC 6.5V 50W |
| MAX5479ETE+T | IC POT DGTL DUAL 256-TAP 16-TQFN |
| V28A24H200BL | CONVERTER MOD DC/DC 24V 200W |
| MAX5479EUD+T | IC POT DGTL DUAL 256-TAP 14TSSOP |
| V28A24H200B2 | CONVERTER MOD DC/DC 24V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5478EVCMODU | 功能描述:数字电位计 IC Evaluation Kit/Evaluation System for the MAX5477/MAX5478/MAX5479 RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| MAX5478EVKIT | 功能描述:数字电位计 IC Evaluation Kit/Evaluation System for the MAX5477/MAX5478/MAX5479 RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| MAX5479ETE | 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| MAX5479ETE#G16 | 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| MAX5479ETE#TG16 | 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。