- 您现在的位置：买卖IC网 > PDF目录8867 > MAX5480AEEE+ (Maxim Integrated Products)IC DAC 8BIT PARALLEL 16-QSOP PDF资料下载
参数资料
| 型号： | MAX5480AEEE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 4/6页 |
| 文件大小： | 0K |
| 描述： | IC DAC 8BIT PARALLEL 16-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 设置时间： | 400ns |
| 位数： | 8 |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 管件 |
| 输出数目和类型： | 2 电流，单极；2 电流，双极；2 电压，单极；2 电压，双极 |
| 采样率（每秒）： | * |
| 产品目录页面： | 1397 (CN2011-ZH PDF) |
MAX5480
_______________Detailed Description
The MAX5480 is an 8-bit multiplying digital-to-analog
converter (DAC) that consists of a thin-film R-2R resistor
array with CMOS current steering switches. Figure 3
shows a simplified schematic of the DAC. The inverted
R-2R ladder divides the voltage or current reference in
a binary manner among the eight steering switches.
The magnitude of the current appearing at either OUT
terminal depends on the number of switches selected;
therefore, the output is an analog representation of the
digital input. The two OUT terminals must be held at the
same potential so a constant current is maintained in
each ladder leg. This makes the REF input current inde-
pendent of switch state and also ensures that the
MAX5480 maintains its excellent linearity performance.
Interface-Logic Information
Mode Selection
The inputs CS and WR control the MAX5480’s operat-
ing mode (see Table 1).
Write Mode
When CS and WR are both low, the MAX5480 is in write
mode, and its analog output responds to data activity at
the D0–D7 data-bus inputs. In this mode, the data
latches are transparent (see Tables 2 and 3).
Hold Mode
In hold mode, the MAX5480 retains the data that was
present on D0–D7 just prior to CS or WR assuming a
high state. The analog output remains at the value cor-
responding to the digital code locked in the data latch.
__________Applications Information
Using the MAX5480 in Voltage-
Output Mode (Single Supply)
The MAX5480 can be used either as a current-output
DAC (Figures 1 and 6) or as a voltage-output DAC
(Figures 2 and 5).
To use the MAX5480 in voltage mode, connect OUT1 to
the reference input and connect OUT2 to ground. REF,
now the DAC output, is a voltage source with a con-
stant output resistance of 10k
(nominally). This output
is often buffered with an op amp (Figure 5).
An advantage of voltage-mode operation is single-
supply operation for the complete circuit; i.e., a nega-
tive reference is not required for a positive output. It is
important to note that the range of the reference is
restricted in voltage mode. The reference input (voltage
at OUT1) must always be positive and is limited to no
more than VDD - 3V. If the reference voltage exceeds
this value, linearity is degraded.
8-Bit Parallel DAC in
QSOP-16 Package
4
_______________________________________________________________________________________
WR
L
H
X
H
CS
MAX5480
10pF
VOUT
16
14
15
VREF
VDD
R2
1k
R1
2k
D7–D0
CS
OUT1
12
DATA
INPUTS 4–11
13
OUT2
1
2
WR
R1 AND R2 USED ONLY IF GAIN
ADJUSTMENT IS REQUIRED.
REF
RFB
GND
3
VDD
MAX4330
Figure 1. Unipolar Binary Operation (Two-Quadrant Multiplication)
MAX5480
REF
INPUT*
OUTPUT
VOLTAGE
(10k
OUTPUT
RESISTANCE)
OUT1
REF
14
15
1
2
16
13
12
3
OUT2
RFB
VDD
+5V
GND
D7–D0
4–11
DATA IN
CS
WR
*(VDD - 3V, max)
Figure 2. Typical Operating Circuit (Voltage Mode—Unbuffered)
MODE
Write
Hold
DAC Response
DAC responds to data bus
(D0–D7) inputs.
Data bus (D0–D7) is locked out;
DAC holds last data present
when CS or WR assumed high
state.
Table 1. Mode-Selection Table
L = Low State, H = High State, X = Don’t Care
相关PDF资料 |
PDF描述 |
|---|---|
| MS27499E18B35A | CONN HSG RCPT 66POS BOX MT PIN |
| MS27513E20B35SLC | CONN HSG RCPT 79POS BOX MT SCKT |
| MS3450KS24-28S | CONN RCPT 24POS WALL MNT W/SCKT |
| D38999/26SJ61SA | CONN PLUG 61POS STRAIGHT W/SCKT |
| MS27499E8F98PLC | CONN HSG RCPT 3POS BOX MNT PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5480AEEE+ | 功能描述:数模转换器- DAC 8-Bit Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5480AEEE+T | 功能描述:数模转换器- DAC 8-Bit Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5480AEEE-T | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5480BCEE | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5480BCEE+ | 功能描述:数模转换器- DAC 8-Bit Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。