参数资料
型号: MAX5486EUG+
厂商: Maxim Integrated Products
文件页数: 16/16页
文件大小: 0K
描述: IC CNTRL VOL STEREO 24TSSOP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 62
类型: 立体声音量控制
应用: 车载系统,台式音频,机顶盒
安装类型: 表面贴装
封装/外壳: 24-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 24-TSSOP
包装: 管件
MAX5486
Stereo Volume Control with Pushbutton
Interface
_______________________________________________________________________________________
9
When both wipers are in the tap 31 position (-62dB
attenuation), further commands to DN/BALR place the
wipers in the mute position (see Table 1). UP/BALL or
MUTE pulses return the wipers to tap 31.
Balance Control
In balance-control mode, the MAX5486 adjusts the bal-
ance between the right and left channels while main-
taining the set volume. For example, if the volume of the
right channel equals the volume of the left channel,
forcing the balance towards the left channel increases
the attenuation of the right channel (Figure 3a). If the
left channel is at a higher attenuation than the right
channel, adjusting the balance to the left channel
moves the left channel’s wiper up to the same wiper
position as the right channel before it was attenuated
(Figure 3b).
Click-and-Pop Suppression
The click-and-pop suppression feature reduces the
audible noise (clicks and pops) that results from wiper
transitions. The MAX5486 minimizes this noise by allow-
ing the wiper to change position only when VH = VL
(zero crossing) or after the zero crossing timeout
(126ms). Each wiper has its own suppression and time-
out circuitry. The MAX5486 changes wiper position
when VH = VL, or after 32ms, whichever occurs first
(see Figures 4a and 4b).
The suppression circuitry monitors left and right chan-
nels separately. In volume-control mode, when the first
_______________________________________________________________________________________
9
WR
H_
L_
WL
WR
WL
PRESS UP
TWICE
PRESS DN
ONCE
NO CHANGE
WR
WL
WR
WL
PRESS UP
ONCE
PRESS UP
ONCE
WR
WL
WR
WL
PRESS DN
ONCE
PRESS DN
ONCE
WR
WL
WR
WL
PRESS UP
ONCE
PRESS UP
ONCE
BALANCE SEPARATION
MAINTAINED
ORIGINAL BALANCE SEPARATION
MAINTAINED
TO 2d
FROM 2c
L_
(2a)
(2b)
(2c)
(2d)
Figures 2a–2d. Volume-Control Operation
相关PDF资料
PDF描述
MAX5679ETJ+T IC GENERATOR PROG LCD 32TQFN
MAX6618AUB+ IC PECI TO I2C TRANSLATOR 10UMAX
MAX6621AUB+ IC TRANSL PECI TO I2C 10-UMAX
MAX7428EKA+T IC FILTER BUFFER VID SOT23-8
MAX7450ESA+T IC CONDITIONER VIDEO 8-SOIC
相关代理商/技术参数
参数描述
MAX5486EUG+ 功能描述:数字电位计 IC Stereo Vol Control w/Pushbutton Int RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel
MAX5486EUG+T 功能描述:数字电位计 IC Stereo Vol Control w/Pushbutton Int RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel
MAX5487ETE 制造商:Maxim Integrated Products 功能描述:DUAL 256-TAP SPI 10K DIGITAL POTENTIOMETER - Rail/Tube
MAX5487ETE#G16 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel
MAX5487ETE#TG16 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel