- 您现在的位置：买卖IC网 > PDF目录2011 > MAX5754UTN+ (Maxim Integrated Products)IC DAC 14BIT 32CHAN SER 56-TQFN PDF资料下载
参数资料
| 型号： | MAX5754UTN+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 8/25页 |
| 文件大小： | 0K |
| 描述： | IC DAC 14BIT 32CHAN SER 56-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 37 |
| 设置时间： | 20µs |
| 位数： | 14 |
| 数据接口： | 串行 |
| 转换器数目： | 32 |
| 电压电源： | 模拟和数字 |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 56-WFQFN 裸露焊盘 |
| 供应商设备封装： | 56-TQFN-EP（8x8） |
| 包装： | 管件 |
| 输出数目和类型： | 32 电压，单极 |
| 采样率（每秒）： | * |
MAX5753/MAX5754/MAX5755
32-Channel, 14-Bit, Voltage-Output
DACs with Serial Interface
16
______________________________________________________________________________________
C2, C1, and C0 = 010, address bits A5–A0 = 111111,
and all data bits to don’t care. See Table 3 for the data
format. This operation updates all DAC outputs.
Note: The software load DAC does not affect the offset DAC.
Clear (
CLR)
The MAX5753/MAX5754/MAX5755 feature an active-low
CLR logic input that sets all channels including the offset
DAC to 0V (code 0000 hex). The offset DAC needs to be
reprogrammed after CLR is asserted. Driving CLR low
clears the contents of both the input and DAC registers.
The serial interface can also issue a software clear com-
mand. Setting the control bits C2, C1, and C0 = 111
(Table 4) performs the same function as driving logic-
input CLR low. Table 4 shows the clear-data format for
the software-controlled clear command. This register-
reset process cannot be interrupted. All serial input data
is ignored until the entire reset process is complete.
Serial Interface
A 3-wire SPI-/QSPI-/MICROWIRE-/DSP-compatible serial
interface controls the MAX5753/MAX5754/MAX5755.
The interface requires a 32-bit command word to control
the device. The command word consists of 3 control
bits, 6 address bits, 7 don’t-care bits, 14 data bits, and
S1 and S0 (don’t-care bits). Table 5 shows the general
serial-data format. The control bits control various write
and read commands as well as the load DAC and clear
commands. Table 6 shows the control-bit functions. The
address bits select the register(s) to be written. Table 7
shows the address functions. The data bits control the
value of the DAC outputs.
Table 3. Load-DAC Data Format
CONTROL
BITS
ADDRESS
BITS
DON’T-
CARE
BITS
DATA BITS*
C2, C1,
AND C0
A5–A0
—
D13–D0,
S1 AND S0
010
111111
XXXXXXX
XXXXXXXXXXXXXXXX
Table 4. Clear-Data Format
CONTROL
BITS
ADDRESS
BITS
DON’T-
CARE
BITS
DATA BITS*
C2, C1,
AND C0
A5–A0
—
D13–D0,
S1 AND S0
111
See table
XXXXXXX
XXXXXXXXXXXXXXXX
Table 5. Serial-Data Format
CONTROL
BITS
ADDRESS
BITS
DON’T-
CARE
BITS
DATA BITS*
MSB
LSB
C2, C1,
and C0
A5–A0
XXXXXXX
D13–D0, S1 and S0
Table 6. Control-Bit Functions
CONTROL
BITS
C2 C1 C0
CONTROL-BIT DESCRIPTION
00
0
No operation (NOP); no internal registers
change state. The NOP command can be
passed to DOUT depending on the state of the
configuration register. Address bits A5–A0 and
data bits D13–D0 are ignored.
00
1
Loads D13–D0 into the input register(s) for the
selected address. Depending on the address
bits, this command could write to:
The configuration register (A[5:0] = 100001)
One of the input registers of the 32 DAC channels
All 32 DAC input registers (A[5:0] = 111111)
The offset DAC input register (A[5:0] = 100000)
01
0
Loads DAC register(s) from the input register(s).
Depending on the address bits, this command
can update one or all of the DAC registers from
the stored input register value(s). Data bits
D13–D0 are ignored.
01
1
Write-through; loads D13–D0 into the input and
DAC registers, depending on the address bits.
10
0
Read command; depending on the address bits,
one of the DAC-register values or the
configuration-register value may be read back
through DOUT. Data bits D13–D0 are ignored.
1
0
1
Reserved for internal testing; do not use.
1
0
Reserved for internal testing; do not use.
11
1
Clear register(s); depending on the address bits,
one or all registers (except the offset-DAC registers)
are cleared to zero. Data bits D13–D0 are ignored.
*S1 and S0 are empty bits—set to zero.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5774UCB+D | IC DAC 14BIT 32CHAN SER 64-TQFP |
| MAX5811PEUT+T | IC DAC SERIAL 10BIT 1CH SOT23-6 |
| MAX5812PEUT+T | IC DAC SERIAL 12BIT 1CH SOT23-6 |
| MAX5815AAUD+T | IC DAC 12BIT SRL 4CH 14TSSOP |
| MAX5816ATB+T | IC DAC 12BIT SRL 4CH 10TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5754UTN+ | 功能描述:数模转换器- DAC 10-Bit 32Ch Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5754UTN+T | 功能描述:数模转换器- DAC 10-Bit 32Ch Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5754UTN-T | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5755ETN | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5755UCB | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。