- 您现在的位置：买卖IC网 > PDF目录8538 > MAX5811NEUT+T (Maxim Integrated Products)IC DAC SERIAL 10BIT 1CH SOT23-6 PDF资料下载
参数资料
| 型号： | MAX5811NEUT+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/13页 |
| 文件大小： | 0K |
| 描述： | IC DAC SERIAL 10BIT 1CH SOT23-6 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 设置时间： | 4µs |
| 位数： | 10 |
| 数据接口： | 串行 |
| 转换器数目： | 1 |
| 电压电源： | 单电源 |
| 功率耗散（最大）： | 727mW |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-6 |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 1 电压，单极 |
| 采样率（每秒）： | * |
MAX5811
10-Bit Low Power 2-Wire Interface Serial,
Voltage-Output DAC
8
_______________________________________________________________________________________
a serial clock line (SCL). The MAX5811 is SMBus com-
patible within the range of VDD = 2.7V to 3.6V. SDA and
SCL facilitate bidirectional communication between the
MAX5811 and the master at rates up to 400kHz. Figure
1 shows the 2-wire interface timing diagram. The
MAX5811 is a transmit/receive slave-only device, rely-
ing upon a master to generate a clock signal. The mas-
ter (typically a microcontroller) initiates data transfer on
the bus and generates SCL to permit that transfer.
A master device communicates to the MAX5811 by
transmitting the proper address followed by command
and/or data words. Each transmit sequence is framed
by a START (S) or REPEATED START (Sr) condition and
a STOP (P) condition. Each word transmitted over the
bus is 8 bits long and is always followed by an
acknowledge clock pulse.
The MAX5811 SDA and SCL drivers are open-drain
outputs, requiring a pullup resistor (500
or greater) to
generate a logic high voltage (see Typical Operating
Circuit). Series resistors RS are optional. These series
resistors protect the input stages of the MAX5811 from
high-voltage spikes on the bus lines, and minimize
crosstalk and undershoot of the bus signals.
Bit Transfer
One data bit is transferred during each SCL clock
cycle. The data on SDA must remain stable during the
high period of the SCL clock pulse. Changes in SDA
while SCL is high are control signals (see START and
STOP Conditions). SDA and SCL idle high when the
I2C bus is not busy.
START and STOP Conditions
When the serial interface is inactive, SDA and SCL idle
high. A master device initiates communication by issu-
ing a START condition. A START condition is a high-to-
Figure 1. 2-Wire Serial lnterface Timing Diagram
SCL
SDA
STOP
CONDITION
START
CONDITION
REPEATED START CONDITION
START CONDITION
tLOW
tSU, DAT
tSU, STA
tSP
tBUF
tHD, STA
tSU, STO
tR
tF
tHD, STA
tHIGH
tHD, DAT
SCL
SDA
SSr
P
Figure 2. START/STOP Conditions
Figure 3. Early STOP Condition
SCL
SDA
STOP
START
SCL
SDA
ILLEGAL
STOP
START
ILLEGAL EARLY STOP CONDITION
LEGAL STOP CONDITION
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B31-MU-F3 | CONVERTER MOD DC/DC 12V 200W |
| VI-B10-MX-S | CONVERTER MOD DC/DC 5V 75W |
| MAX5811MEUT+T | IC DAC SERIAL 10BIT 1CH SOT23-6 |
| VI-B31-MU-F1 | CONVERTER MOD DC/DC 12V 200W |
| LT1189CS8 | IC AMP VIDEO DIFFRNC ADJ 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5811PEUT | 制造商:Maxim Integrated Products 功能描述:10-BIT LOW-POWER 2-WIRE SERIAL V - Rail/Tube |
| MAX5811PEUT+T | 功能描述:数模转换器- DAC 10-Bit Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5811PEUT-T | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5812LEUT | 制造商:Maxim Integrated Products 功能描述:12-BIT LOW-POWER 2-WIRE SERIAL V - Rail/Tube |
| MAX5812LEUT+ | 制造商:Maxim Integrated Products 功能描述:12-BIT LOW-POWER, 2-WIRE, SERIAL VOLTAGE-OUTPUT DAC - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。