- 您现在的位置：买卖IC网 > PDF目录8940 > MAX5820LEUA+ (Maxim Integrated Products)IC DAC 8BIT DUAL 2WIRE SER 8UMAX PDF资料下载
参数资料
| 型号： | MAX5820LEUA+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/13页 |
| 文件大小： | 0K |
| 描述： | IC DAC 8BIT DUAL 2WIRE SER 8UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 设置时间： | 4µs |
| 位数： | 8 |
| 数据接口： | 串行 |
| 转换器数目： | 2 |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 管件 |
| 输出数目和类型： | 2 电压，单极 |
| 采样率（每秒）： | * |
| 产品目录页面： | 1398 (CN2011-ZH PDF) |
MAX5820
The MAX5820 SDA and SCL drivers are open-drain out-
puts, requiring a pullup resistor to generate a logic high
voltage (see the Typical Operating Circuit ). Series
resistors RS are optional. These series resistors protect
the input stages of the MAX5820 from high-voltage
spikes on the bus lines, and minimize crosstalk and
undershoot of the bus signals.
Bit Transfer
One data bit is transferred during each SCL clock
cycle. The data on SDA must remain stable during the
high period of the SCL clock pulse. Changes in SDA
while SCL is high are control signals (see the START
and STOP Conditions section). Both SDA and SCL idle
high when the I2C bus is not busy.
START and STOP Conditions
When the serial interface is inactive, SDA and SCL idle
high. A master device initiates communication by issu-
ing a START condition. A START condition is a high-to-
low transition on SDA with SCL high. A STOP condition
is a low-to-high transition on SDA, while SCL is high
(Figure 2). A START condition from the master signals
the beginning of a transmission to the MAX5820. The
master terminates transmission by issuing a not
acknowledge followed by a STOP condition (see the
Acknowledge Bit (ACK) section). The STOP condition
frees the bus. If a repeated START condition (Sr) is
generated instead of a STOP condition, the bus
remains active. When a STOP condition or incorrect
address is detected, the MAX5820 internally discon-
nects SCL from the serial interface until the next START
condition, minimizing digital noise and feedthrough.
Early STOP Conditions
The MAX5820 recognizes a STOP condition at any
point during transmission except if a STOP condition
occurs in the same high pulse as a START condition
(Figure 3). This condition is not a legal I2C format; at
least one clock pulse must separate any START and
STOP conditions.
Repeated START Conditions
A repeated START (Sr) condition may indicate a
change of data direction on the bus. Such a change
occurs when a command word is required to initiate a
read operation. Sr may also be used when the bus
master is writing to several I2C devices and does not
want to relinquish control of the bus. The MAX5820 seri-
al interface supports continuous write operations with or
without an Sr condition separating them. Continuous
read operations require Sr conditions because of the
change in direction of data flow.
Dual, 8-Bit, Low-Power, 2-Wire, Serial
Voltage-Output DAC
8
_______________________________________________________________________________________
POWER-DOWN
COMMAND BITS
PD1
PD0
MODE/FUNCTION
00
Power-up device. DAC output
restored to previous value.
01
Power-down mode 0. Power down
device with output floating.
10
Power-down mode 1. Power down
device with output terminated with
1k
to GND.
11
Power-down mode 2. Power down
device with output terminated with
100k
to GND.
Table 1. Power-Down Command Bits
SCL
SDA
STOP
CONDITION
START
CONDITION
REPEATED START CONDITION
START CONDITION
tLOW
tSU, DAT
tSU, STA
tSP
tBUF
tHD, STA
tSU, STO
tF
tHD, STA
tHIGH
tHD, DAT
tR
Figure 1. 2-Wire Serial-Interface Timing Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| PI6C2408-3WE | IC 4+4 0-DELAY CLK BUFF 16-SOIC |
| PI6C2408-2WE | IC 4+4 0-DELAY CLK BUFF 16-SOIC |
| VI-J4K-MZ-F1 | CONVERTER MOD DC/DC 40V 25W |
| VI-J4J-MZ-F4 | CONVERTER MOD DC/DC 36V 25W |
| VI-JV2-MZ-F4 | CONVERTER MOD DC/DC 15V 25W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5820LEUA+ | 功能描述:数模转换器- DAC 8-Bit 2Ch Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5820LEUA+T | 功能描述:数模转换器- DAC 8-Bit 2Ch Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5820LEUA-T | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5820MEUA | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5820MEUA+ | 功能描述:数模转换器- DAC 8-Bit 2Ch Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。