- 您现在的位置：买卖IC网 > PDF目录8521 > MAX5841LEUB+T (Maxim Integrated Products)IC DAC 10BIT QUAD 2WIRE 10-UMAX PDF资料下载
参数资料
| 型号： | MAX5841LEUB+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/15页 |
| 文件大小： | 0K |
| 描述： | IC DAC 10BIT QUAD 2WIRE 10-UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 设置时间： | 4µs |
| 位数： | 10 |
| 数据接口： | 串行 |
| 转换器数目： | 4 |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-µMAX |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 4 电压，单极 |
| 采样率（每秒）： | * |
MAX5841
Quad, 10-Bit, Low-Power, 2-Wire, Serial
Voltage-Output DAC
8
_______________________________________________________________________________________
Detailed Description
The MAX5841 is a quad, 10-bit, voltage-output DAC
with an I2C/SMBus-compatible 2-wire interface. The
device consists of a serial interface, power-down cir-
cuitry, four input and DAC registers, four 10-bit resistor
string DACs, four unity-gain output buffers, and output
resistor networks. The serial interface decodes the
address and control bits, routing the data to the proper
input or DAC register. Data can be directly written to
the DAC register, immediately updating the device out-
put, or can be written to the input register without
changing the DAC output. Both registers retain data as
long as the device is powered.
DAC Operation
The MAX5841 uses a segmented resistor string DAC
architecture, which saves power in the overall system
and guarantees output monotonicity. The MAX5841’s
input coding is straight binary, with the output voltage
given by the following equation:
where N = 10 (bits), and D = the decimal value of the
input code (0 to 1023).
Output Buffer
The MAX5841 analog outputs are buffered by preci-
sion, unity-gain followers that slew 0.5V/s. Each buffer
output swings rail-to-rail, and is capable of driving 5k
in parallel with 200pF. The output settles to ±0.5LSB
within 4s.
Power-On Reset
The MAX5841 features an internal POR circuit that ini-
tializes the device upon power-up. The DAC registers
are set to zero scale and the device is powered down,
with the output buffers disabled and the outputs pulled
to GND through the 100k
termination resistor.
Following power-up, a wake-up command must be initi-
ated before any conversions are performed.
Power-Down Modes
The MAX5841 has three software-controlled low-power
power-down modes. All three modes disable the output
buffers and disconnect the DAC resistor strings from
REF, reducing supply current draw to 1A and the ref-
erence current draw to less than 1A. In power-down
mode 0, the device output is high impedance. In
power-down mode 1, the device output is internally
pulled to GND by a 1k
termination resistor. In power-
down mode 2, the device output is internally pulled to
GND by a 100k
termination resistor. Table 1 shows
the power-down mode command words.
Upon wake-up, the DAC output is restored to its previ-
ous value. Data is retained in the input and DAC regis-
ters during power-down mode.
Digital Interface
The MAX5841 features an I2C/SMBus-compatible
2-wire interface consisting of a serial data line (SDA)
and a serial clock line (SCL). The MAX5841 is SMBus
compatible within the range of VDD = 2.7V to 3.6V. SDA
and SCL facilitate bidirectional communication between
the MAX5841 and the master at rates up to 400kHz.
Figure 1 shows the 2-wire interface timing diagram. The
MAX5841 is a transmit/receive slave-only device, rely-
ing upon a master to generate a clock signal. The mas-
ter (typically a microcontroller) initiates data transfer on
the bus and generates SCL to permit that transfer.
A master device communicates to the MAX5841 by
transmitting the proper address followed by command
and/or data words. Each transmit sequence is framed-
V
VD
OUT
REF
N
_
()
=
×
2
Pin Description
PIN
NAME
FUNCTION
1
ADD
Address Select. A logic high sets the address LSB to 1; a logic low sets the address LSB to zero.
2
SCL
Serial Clock Input
3VDD
Power Supply
4
GND
Ground
5
SDA
Bidirectional Serial Data Interface
6
REF
Reference Input
7
OUTA
DAC A Output
8
OUTB
DAC B Output
9
OUTC
DAC C Output
10
OUTD
DAC D Output
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B21-MW | CONVERTER MOD DC/DC 12V 100W |
| VE-23Z-MV | CONVERTER MOD DC/DC 2V 60W |
| MAX5355EUA+T | IC DAC 10BIT 3.3V VOLT OUT 8UMAX |
| MAX5104CEE+T | IC DAC 12BIT DUAL SER 16-QSOP |
| MAX9585AUB+ | IC AMP VIDEO FILTER 10-UMAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5841MEUB | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5841MEUB+ | 功能描述:数模转换器- DAC 10-Bit 4Ch Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5841MEUB+T | 功能描述:数模转换器- DAC 10-Bit 4Ch Precision DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5841MEUB-T | 功能描述:数模转换器- DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MAX5842EUB | 制造商:Maxim Integrated Products 功能描述:QUAD, 12-BIT, LOW-POWER, 2-WIRE, SERIAL VOLTA - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。