- 您现在的位置：买卖IC网 > PDF目录180478 > MAX5961ETM+ (MAXIM INTEGRATED PRODUCTS INC) 0 to 16V, Quad, Hot-Swap Controller with 10-Bit Current and Voltage Monitor; Package: THIN QFN, 48 pin ; Temperature Range: -40°C to +85°C PDF资料下载
参数资料
| 型号： | MAX5961ETM+ |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | 0 to 16V, Quad, Hot-Swap Controller with 10-Bit Current and Voltage Monitor; Package: THIN QFN, 48 pin ; Temperature Range: -40°C to +85°C |
| 中文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, QCC48 |
| 封装： | 7 X 7 MM, ROHS COMPLIANT, MO-220, TQFN-48 |
| 文件页数： | 11/42页 |
| 文件大小： | 335K |
| 代理商： | MAX5961ETM+ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
MAX5961
0 to 16V, Quad, Hot-Swap Controller
with 10-Bit Current and Voltage Monitor
______________________________________________________________________________________
19
Startup
When all conditions for channel turn-on are met, the
external n-channel MOSFET switch is fully enhanced
with a typical gate-to-source voltage of 5.5V to ensure a
low drain-to-source resistance. The charge pump at
each GATE_ driver sources 5A to control the output-
voltage turn-on slew rate. An external capacitor can be
added from GATE_ to GND_ to further reduce the volt-
age slew rate. Placing a 1kΩ resistor in series with this
capacitance will prevent the added capacitance from
increasing the gate turn-off time; see the
Typical
Application Circuit. Total inrush current is the load cur-
rent summed with the product of the gate voltage slew
rate dv/dt and the load capacitance.
To determine the output dv/dt during startup, divide the
GATE_ pullup current IG(UP) by the gate-to-ground
capacitance. The voltage at the source of the external FET
follows the gate voltage, so the load dv/dt is the same as
the gate dv/dt. Inrush current is the product of the dv/dt
and the load capacitance. The time to start up tSU is the
hot-swap voltage VS_ divided by the output dv/dt.
Be sure to choose an external MOSFET that can handle
the power dissipated during startup. The inrush current
is roughly constant during startup, and the voltage drop
across the FET (drain to source) decreases linearly as
the load capacitance charges. The resulting power dissi-
pation is therefore roughly equivalent to a single pulse of
magnitude (VS_ x I_INRUSH)/2 and duration tSU. Refer to
the thermal resistance charts in the MOSFET data sheet
to determine the junction temperature rise during startup,
and ensure that this does not exceed the maximum junc-
tion temperature for worst-case ambient conditions.
Circuit-Breaker Protection
As the channel is turned on and during normal opera-
tion, two analog comparators are used to detect an
overcurrent condition by sensing the voltage across an
external resistor connected between SENSE_ and
MON_. If the voltage across the sense resistor is less
than the slow-trip and fast-trip circuit-breaker thresh-
olds, the GATE_ output remains high. If either of the
thresholds are exceeded due to an overcurrent condi-
tion, the gate of the MOSFET is pulled down to MON_
by an internal 500mA current source.
The higher of the two comparator thresholds, the fast-
trip, is set by an internal 8-bit DAC (see Table 8), within
one of three configurable full-scale current-sense
ranges: 25mV, 50mV, or 100mV (see Tables 7a and
7b). The 8-bit fast-trip threshold DAC can be pro-
grammed from 40% to 100% of the selected full-scale
current-sense range. The slow-trip threshold follows the
fast-trip threshold as one of four programmable ratios,
set by the ifast2slow register (see Tables 5a and 5b).
Table 5a. ifast2slow Register Format
Description:
Fast-trip to slow-trip threshold ratio setting bits
Register Title:
ifast2slow
Register Address:
0x5E
R/W
RESET
VALUE
Ch4_FS1
Ch4_FS0
Ch3_FS1
Ch3_FS0
Ch2_FS1
Ch2_FS0
Ch1_FS1
Ch1_FS0
0xFF
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Table 5b. Setting Fast-Trip to Slow-Trip Threshold Ratio
Chx_FS1
Chx_FS0
FAST-TRIP TO SLOW-TRIP RATIO (%)
0
125
0
1
150
1
0
175
1
200
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5965AEAX+ | High-Power, Quad, Monolithic, PSE Controllers for Power over Ethernet; Package: SSOP;36 pin;163 mm² ; Temperature: -40°C to +85°C |
| MAX5965AUAX+ | High-Power, Quad, Monolithic, PSE Controllers for Power over Ethernet; Package: SSOP;36 pin;163 mm² ; Temperature: 0°C to +85°C |
| MAX5965BEAX+ | High-Power, Quad, Monolithic, PSE Controllers for Power over Ethernet; Package: SSOP;36 pin;163 mm² ; Temperature: -40°C to +85°C |
| MAX5965BUAX+ | High-Power, Quad, Monolithic, PSE Controllers for Power over Ethernet; Package: SSOP;36 pin;163 mm² ; Temperature: 0°C to +85°C |
| MAX6317HUK25AW-T | Versatile Customizable SOT Reset + Watchdog ICs Offer 3224 Unique Options[Japanese] |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5961ETM+ | 功能描述:热插拔功率分布 Quad Hot-Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5961ETM+T | 功能描述:热插拔功率分布 Quad Hot-Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5961EVKIT+ | 功能描述:电源管理IC开发工具 MAX5961 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX5963UTL+ | 功能描述:热插拔功率分布 Dl 7.5-76V Hot-Swap & Diode ORing Ctlr RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5963UTL+T | 功能描述:热插拔功率分布 Dl 7.5-76V Hot-Swap & Diode ORing Ctlr RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。