- 您现在的位置：买卖IC网 > PDF目录19751 > MAX5965BUAX+T (Maxim Integrated)IC PSE CTRLR FOR POE 36SSOP PDF资料下载
参数资料
| 型号： | MAX5965BUAX+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 37/54页 |
| 文件大小： | 1334K |
| 描述： | IC PSE CTRLR FOR POE 36SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,000 |
| 类型： | 以太网供电控制器（PoE） |
| 应用： | IP 电话，LAN 网络供电，网络路由器和交换机 |
| 内部开关： | 无 |
| 电源电压： | 2.4 V ~ 3.6 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-BSOP（0.295"，7.50mm 宽） |
| 供应商设备封装： | 36-SSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页当前第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页
High-Power, Quad, Monolithic, PSE Controllers
for Power over Ethernet
______________________________________________________________________________________ 37
Setting CL_DISC to 1 (Table 21) enables port over class
current protection, where the MAX5965A/MAX5965B
scales down the overcurrent limit (V
FLT_LIM
) according
to the port classification status. This feature provides
protection to the system against PDs that violate their
maximum class current allowance.
The MAX5965 is programmed to switch to a high-power
configuration and HP_TIME is low, the higher current set-
ting is enabled only after a successful startup so that the
PD powers up as a normal 15W device. If HP_TIME is set
together with EN_HP_ALL, the higher current setting will
be active before startup. For Classes 4, 5, and 6, the
corresponding enable bit in register R15h must be set
together with EN_HP_ALL. In any other cases, the cur-
rent level defaults to Class 0.
CL_DISC, together with EN_HP_CL_ (R15h[6:4]),
EN_HP_ALL (R15h[7]), and ENx_CL6 (R1Ch[7:4]) are
used to program the high-power mode. See Table 3 for
details.
Setting OUT_ISO high (Table 21), forces DET_ to a
high-impedance state.
A reset sets R17h = 0xC0.
Table 21. Miscellaneous Configurations 1 Register
ADDRESS = 17h
SYMBOL
BIT
R/W
DESCRIPTION
INT_EN
7
R/W
A logic-high enables INT functionality
RSTR_EN
6
R/W
A logic-high enables the autorestart protection time off (as set by the RSTR[1:0] bits)
Reserved
5
Reserved
Reserved
4
Reserved
POFF_CL
3
R
A logic-high prevents power-up after a classification failure (I > 50mA, valid only in AUTO
mode)
CL_DISC
2
R/W
A logic-high enables reduced current-limit voltage threshold (V
FLT_LIM
) according to port
classification result
OUT_ISO
1
R/W
Forces DET_ to high impedance. Does not interfere with other circuit operation.
HP_TIME
0
R/W
Enables high power after startup.
Table 22. Power-Enable Pushbuttons Register
ADDRESS = 19h
SYMBOL
BIT
R/W
DESCRIPTION
PWR_OFF4
7
W
A logic-high powers off port 4
PWR_OFF3
6
W
A logic-high powers off port 3
PWR_OFF2
5
W
A logic-high powers off port 2
PWR_OFF1
4
W
A logic-high powers off port 1
PWR_ON4
3
W
A logic-high powers on port 4
PWR_ON3
2
W
A logic-high powers on port 3
PWR_ON2
1
W
A logic-high powers on port 2
PWR_ON1
0
W
A logic-high powers on port 1
Power-enable pushbutton for semi and manual modes
is found in Table 22. Setting PWR_ON_ to 1 turns on
power to the corresponding port. Setting PWR_OFF_ to
1 turns off power to the port. PWR_ON_ is ignored when
the port is already powered and during shutdown.
PWR_OFF_ is ignored when the port is already off and
during shutdown. After execution, the bits reset to 0.
During detection or classification, if PWR_ON_ goes
high, the MAX5965A/MAX5965B gracefully terminate
the current operation and turn on power to the port. The
MAX5965A/MAX5965B ignore the PWR_ON_ in auto
mode. A reset sets R19h = 00h.
相关PDF资料 |
PDF描述 |
|---|---|
| MIC29151-3.3BU TR | IC REG LDO 3.3V 1.5A TO-263-5 |
| VI-25Z-CW-F1 | CONVERTER MOD DC/DC 2V 40W |
| EEM03DSEN | CONN EDGECARD 6POS .156 EYELET |
| VI-25Y-CY-F4 | CONVERTER MOD DC/DC 3.3V 33W |
| TAP335K025FCS | CAP TANT 3.3UF 25V 10% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5967BETG+ | 功能描述:热插拔功率分布 I2C Hot Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5967BETG+T | 功能描述:热插拔功率分布 I2C Hot Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5967BUTG+ | 功能描述:热插拔功率分布 I2C Hot Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5967BUTG+T | 功能描述:热插拔功率分布 I2C Hot Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5967CETG+ | 功能描述:热插拔功率分布 I2C Hot Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。