参数资料
| 型号： | MAX5970EVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 32/41页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT MAX5970 |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
0V to 16V, Dual Hot-Swap Controller with 10-Bit
Current and Voltage Monitor and 4 LED Drivers
If the circular buffer contents are retrieved as 10-bit
data, the first byte read out is the high-order 8 bits of the
10-bit sample, and the second byte read out contains
the two least-significant bits (LSBs) of the sample. This is
repeated for each of the 50 samples in the buffer. Thus,
2 bytes must be read for each 10-bit sample retrieved.
Conversely, if the buffer contents are retrieved as 8-bit
data, then each byte read out contains the 8 MSB of
each successive sample. It is important to remember
that in 10-bit mode, 100 bytes must be read to extract the
entire buffer contents, but in 8-bit mode, only 50 bytes
must be read.
The circular buffer system has a user-programmable
stop delay that specifies a certain number of sample
cycles to continue recording to the buffer after a shut-
down occurs. This delay value is stored in register
cbuf_dly_stop[5:0] (see Table 44).
Table 44. Circular Buffer Stop-Delay Register Format
Description:
Register Title:
Register Address:
Circular buffer stop-delay: any integer number between 0 and 50 samples that are to be recorded
to a buffer after a shutdown event, before the buffer stops storing new data.
cbuf_dly_stop
0x40
R
R
R
R
R
R
R
R
RESET
VALUE
0
0
0x19
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
The default (reset) value of the buffer stop-delay is 25
samples, which means that an equal number of samples
are stored in the buffer preceding and following the
moment of the shutdown event. The buffer stop delay
is analogous to an oscilloscope trigger delay, because
it allows the MAX5970 to record what happened both
immediately before and after a shutdown. In other words,
when the contents of a circular buffer are read out of the
MAX5970, the shutdown event, by default, is located in
the middle of the recorded data. The balance of data
before and after an event can be altered by writing a dif-
ferent value (between 0 and 50) to the buffer stop-delay
register.
Autoretry or Latched-Off Fault Management
In the event of an overcurrent, undervoltage, or overvolt-
age condition that results in the shutdown of one or both
channels, the MAX5970 device can be configured to
either latch off or automatically restart the affected chan-
nel. The MAX5970 stays off if the RETRY input is set low
(latched-off), and automatically retries if the RETRY input
is high. The RETRY input is read once during initialization
and sets the value of status3[6] register (see Table 30).
The autoretry feature has a fixed 200ms timeout delay
between fault shutdown and the autorestart attempt. Be
aware that if the MAX5970 is configured for autoretry
operation, the startup event occurs every 200ms if a
short circuit occurs. A short circuit during startup causes
the output current to increase rapidly as the MOSFET
is enhanced, until the slow-trip threshold is reached
and the gate is pulled low again. Be sure to evaluate
MOSFET junction temperature rise for this repeated-
stress condition if autoretry is used.
To restart a channel that has been shutdown in latched-
off operation (RETRY low), the user must either cycle
power to the IN pin, or toggle one or more of the ON_
pin, Chx_EN1 bit, or the Chx_EN2 bit for the affected
channel.
32
_____________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5976BEVKIT+ | EVAL KIT MAX5976B |
| MAX5977AEVKIT# | EVAL KIT MAX5977A |
| MAX5980EVKIT# | EVAL KIT MAX5980 |
| MAX5982CEVKIT# | EVAL KIT MAX5982C |
| MAX6397SATA+T | IC SW OVERVOLT PROT 8-TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5970EVKIT+ | 功能描述:电源管理IC开发工具 MAX5970 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX5971AETI+ | 功能描述:热插拔功率分布 IEEE 802.3af/at PSE Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5971AETI+T | 功能描述:热插拔功率分布 IEEE 802.3af/at PSE Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5971AETI+W | 制造商:Maxim Integrated Products 功能描述:IEEE802.3 AT PSE SWITCH - Rail/Tube |
| MAX5971AEVKIT | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。