参数资料
型号: MAX5975AETE+
厂商: Maxim Integrated Products
文件页数: 13/20页
文件大小: 0K
描述: IC REG CTRLR FLYBK ISO CM 16TQFN
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 1
PWM 型: 电流模式
输出数: 1
频率 - 最大: 600kHz
占空比: 84%
降压:
升压:
回扫:
反相:
倍增器:
除法器:
Cuk:
隔离:
工作温度: -40°C ~ 85°C
封装/外壳: 16-WFQFN 裸露焊盘
包装: 管件
Current-Mode PWM Controllers with Frequency
Dithering for EMI-Sensitive Power Supplies
Because the MAX5975B is designed for use with low-
V S
R IN
IN
voltage power sources such as wall adapters outputting
12V to 24V, it has a lower UVLO wakeup threshold of 10V.
Startup Operation
The device starts up when the voltage at IN exceeds 20V
(MAX5975A) or 10V (MAX5975B) and the enable input
voltage is greater than 1.26V.
R EN1
C IN
MAX5975
During normal operation, the voltage at IN is normally
derived from a tertiary winding of the transformer.
However, at startup there is no energy being deliv-
ered through the transformer; hence, a special boot-
strap sequence is required. In the Typical Applications
DIGITAL
CONTROL
N
R EN2
EN
Circuits , C IN charges through the startup resistor, R IN , to
an intermediate voltage. Only 100 F A of the current sup-
plied through R IN is used by the ICs, the remaining input
current charges C IN until V IN reaches the bootstrap
UVLO wakeup level. Once V IN exceeds this level, NDRV
begins switching the n-channel MOSFET and transfers
energy to the secondary and tertiary outputs. If the volt-
age on the tertiary output builds to higher than 7V (the
bootstrap UVLO shutdown level), then startup has been
Figure 1. Programmable UVLO for the Power Source
V S
R IN
IN
accomplished and sustained operation commences.
If V IN drops below 7V before startup is complete, the
device goes back to low-current UVLO. In this case,
increase the value of C IN to store enough energy to allow
the voltage at the tertiary winding to build up.
Soft-Start
A capacitor from SS to GND, C SS , programs the soft-
start time. V SS controls the oscillator duty cycle during
startup to provide a slow and smooth increase of the
duty cycle to its steady-state value. Calculate the value
of C SS as follows:
C SS = SS-CH SS
C IN
DIGITAL
CONTROL
N
EN
MAX5975
I × t
2V
where I SS-CH (10 F A typ) is the current charging C SS dur-
ing soft-start and t SS is the programmed soft-start time.
A resistor can also be added from the SS pin to GND to clamp
V SS < 2V and, hence, program the maximum duty cycle to be
less than 80% (see the Duty-Cycle Clamping section).
n-Channel MOSFET Gate Driver
The NDRV output drives an external n-channel MOSFET.
NDRV can source/sink in excess of 650mA/1000mA peak
current; therefore, select a MOSFET that yields acceptable
Figure 2. External Control of the Enable Input
conduction and switching losses. The external MOSFET
used must be able to withstand the maximum clamp voltage.
13
相关PDF资料
PDF描述
MAX5974BETE+ IC REG CTRLR FLYBACK PWM 16-TQFN
MAX5068BAUE+ IC REG CTRLR FLYBK ISO 16-TSSOP
MAX5068EAUE+ IC REG CTRLR FLYBK ISO 16-TSSOP
MAX5061EUE+T IC REG CTRLR BUCK PWM CM 16TSSOP
VI-24F-EW-F4 CONVERTER MOD DC/DC 72V 100W
相关代理商/技术参数
参数描述
MAX5975AETE+ 功能描述:电流型 PWM 控制器 Current-Mode PWM Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
MAX5975AETE+T 功能描述:电流型 PWM 控制器 Current-Mode PWM Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
MAX5975BETE+ 功能描述:电流型 PWM 控制器 Current-Mode PWM Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
MAX5975BETE+T 功能描述:电流型 PWM 控制器 Current-Mode PWM Controller RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14
MAX5975CETE+ 制造商:Maxim Integrated Products 功能描述:CURRENT-MODE PWM CONTROLLERS WITH FREQUENCY DITHERING FOR EM - Rail/Tube