- 您现在的位置：买卖IC网 > PDF目录19776 > MAX5977AETP+T (Maxim Integrated)IC CTLR SNGL-CH HOT-SWAP 20TQFN PDF资料下载
参数资料
| 型号： | MAX5977AETP+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 11/13页 |
| 文件大小： | 0K |
| 描述： | IC CTLR SNGL-CH HOT-SWAP 20TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电流限制： | 可调 |
| 电源电压： | 2.7 V ~ 16 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 供应商设备封装： | 20-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
1V to 16V, Single-Channel, Hot-Swap Controllers
with Precision Current-Sensing Output
An output resistor, R CSOUT , must be connected between
the transconductance current-sense amplifier output
(d = t SU /(t SU + t RETRY )). Calculate the required transient
thermal resistance with the following equation:
CSOUT and AGND. The transconductance G M , of the
amplifier is typically 2500 F S:
R CSOUT × G M × V SENSE, FS ≤ 2.5V
Z θ JA(MAX) ≤
T JMAX × T A
V IN × I INRUSH
n-Channel MOSFET Selection
Select the external n-channel MOSFET according to the
application’s current level. The MOSFET’s on-resistance
(R DS(ON) ) should be chosen low enough to have a mini-
mum voltage drop at full load to limit the MOSFET power
dissipation. High R DS(ON) causes output ripple if there
is a pulsating load. Determine the device power rating to
accommodate a short-circuit condition on the board at
startup and when the device is in automatic-retry mode
(see the MOSFET Thermal Considerations section).
The MAX5977A’s fault latch allows the use of MOSFETs
with lower power ratings. A MOSFET typically withstands
single-shot pulses with higher dissipation than the speci-
fied package rating.
MOSFET Thermal Considerations
During normal operation, the external MOSFETs dis-
sipate little power. The MOSFET R DS(ON) is low when
the MOSFET is fully enhanced. The power dissipated in
normal operation is P D = I LOAD 2 x R DS(ON). The most
power dissipation occurs during the turn-on and turn-off
Layout Considerations
To take full advantage of the switch response time to an
output fault condition, it is important to keep all traces
as short as possible and to maximize the high-current
trace dimensions to reduce the effect of undesirable
parasitic resistance and inductance. Place the devices
close to the card’s connector, and a 0.01 F F capacitor to
GND should be placed as close as possible to V IN . Use
a ground plane to minimize impedance and inductance.
Minimize the current-sense resistor trace length and
ensure accurate current sensing with Kelvin connec-
tions.
When the output is short circuited, the voltage drop
across the external MOSFET becomes large. Hence, the
power dissipation across the switch increases, as does
the die temperature. An efficient way to achieve good
power dissipation on a surface-mount package is to lay
out two copper pads directly under the MOSFET pack-
age on both sides of the board. Connect the two pads to
the ground plane through vias, and use enlarged copper
mounting pads on the top side of the board.
transients when the MOSFETs are in their linear regions.
Take into consideration the worst-case scenario of a
continuous short-circuit fault; consider these two cases:
1) The single turn-on with the device latched after a fault
(MAX5977A).
2) The continuous automatic retry after a fault
(MAX5977B).
MOSFET manufacturers typically include the package
thermal resistance from junction to ambient (R B JA ) and
thermal resistance from junction to case (R B JC ), which
determine the startup time and the retry duty cycle
PART
MAX5970
MAX5978
Related Parts
DESCRIPTION
0 to 16V, Dual Hot-Swap Controller with
a 10-Bit Current and Voltage Monitor and
Four LED Drivers
0 to 16V, Single Hot-Swap Controller with
a 10-Bit Current and Voltage Monitor Plus
Four LED Drivers
11
相关PDF资料 |
PDF描述 |
|---|---|
| MAX5926EEE+T | IC HOT-SWAP CONTROLLER 16QSOP-EP |
| RMA36DRSI-S288 | CONN EDGECARD 72POS .125 EXTEND |
| MAX4272ESA+T | IC CNTRLR HOT SWAP 8-SOIC |
| MAX5920AESA+T | IC HOT-SWAP CTRLR -48V 8-SOIC |
| CDBC360-G | DIODE SCHOTTKY 3A 60V DO-214AB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX5977AEVKIT# | 功能描述:热插拔功率分布 MAX5977A Eval Kit RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5977AEVKIT+ | 功能描述:热插拔功率分布 1V to 16V Hotswap Controller with Precision Current Sensing Output RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5977BETP+ | 功能描述:热插拔功率分布 1-16V Hot-Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5977BETP+T | 功能描述:热插拔功率分布 1-16V Hot-Swap Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MAX5977ETP+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。