参数资料
| 型号： | MAX606EUA+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC DC-DC CONVERT 8-UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 应用： | 转换器，闪存 PCMCIA 卡 |
| 输入电压： | 3 V ~ 5.5 V |
| 输出数： | 1 |
| 输出电压： | 5V，3 V ~ 12.5 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 管件 |
Low-Profile, 5V/12V or Adjustable, Step-Up
DC-DC Converters for Flash Memory/PCMCIA Cards
SS Capacitor graph in the Typical Operating Charac-
INPUT
IN
teristics shows typical timing characteristics for selected
capacitor values and circuit conditions. The soft-start
capacitor is discharged each time the MAX606 or
MAX607 is put into shutdown, including during under-
voltage lockout and when powering down at IN.
If the circuit is required to start up with no load, as in
LX
MAX606
MAX607 OUT
R1
10pF
OUTPUT
flash memory programming supplies, soft-start is not
required. Omitting the soft-start capacitor permits a
minimum output voltage rise time from the shutdown
state, improving flash memory access time.
GND PGND
FB
R2
V OUT = V REF
V REF = 2V
(
R1
R2
+1 )
Undervoltage Lockout
The MAX606/MAX607 monitor the supply voltage at IN
and operate for supply voltages greater than 2.8V.
When an undervoltage condition is detected, control
logic turns off the output power FET and discharges the
Figure 4. Adjustable Output Voltage
When FB is connected to IN or GND, an internal volt-
age divider is configured to produce a predetermined
output. However, when the voltage at FB is between
0.1V above ground and 0.1V below V IN , the device is in
the adjustable output mode. In this mode, the
MAX606/MAX607 output voltage is set by two external
resistors, R1 and R2 (Figure 4), which form a voltage
divider between the output and FB. Use the following
equation to determine the output voltage:
V OUT = V REF (R1 / R2 + 1)
where V REF = 2V. To simplify the resistor selection:
R1 = R2 [(V OUT / V REF ) - 1]
Since the input current at FB is 200nA maximum, large
values (up to 100k ? ) can be used for R2 with no signifi-
cant loss of accuracy. For 1% error, the current through
R2 should be at least 100 times the FB input bias current.
Soft-Start
Connecting a capacitor to the Soft-Start (SS) pin
ensures a gradually increasing current limit during
power-up or when exiting shutdown, thereby reducing
initial inrush currents. This feature can be useful, for
example, when an old battery’s increased series resis-
tance limits initial inrush currents. Using the soft-start
feature in a situation like this minimizes the risk of over-
loading the incoming supply.
Soft-start timing is controlled by the value of the SS
capacitor. On power-up, the SS capacitor is charged by
the 2V reference through an internal, 45k ? pull-up resis-
tor. As the voltage on the SS pin increases, the voltage
at the SS clamp output also increases, which in turn
raises the current-limit threshold. The Start-Up Delay vs.
soft-start capacitor to ground. The control logic holds
the output power FET in an off state until the supply
voltage rises above the undervoltage threshold, at
which time a soft-start cycle begins.
Shutdown Mode
Connecting SHDN to GND will hold the MAX606/
MAX607 in shutdown mode. In shutdown, the output
power FET is off, but there is still an external path from
IN to the load via the inductor and diode. The internal
reference also turns off, which causes the soft-start
capacitor to discharge. Typical device standby current
in shutdown mode is 0.01μA. For normal operation,
connect SHDN to IN. A soft-start cycle is initiated when
the MAX606/MAX607 exit shutdown.
Applications Information
Inductor Selection
Use a 5μH inductor for the MAX606 and a 10μH induc-
tor for the MAX607. See Table 3 for a list of component
suppliers. Higher inductor values allow greater load
currents due to operation in continuous-conduction
mode, while lower inductor values lead to smaller phys-
ical size due to lower energy-storage requirements and
lower output-filter-capacitor requirements. Potential
drawbacks of using lower inductor values are
increased output ripple, lower efficiency, and lower out-
put-current capability due to operation in discontinu-
ous-conduction mode. (See the Maximum Output
Current vs. Inductor Value graph in the Typical
Operating Characteristics.)
The inductor must have a saturation (incremental) cur-
rent rating equal to the peak switch-current limit, which
is 1.1A. For highest efficiency, minimize the inductor’s
DC resistance.
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| 4564-182K | INDUCTOR RF 1.8mH 10% RADIAL |
| SIP21106DVP-26-E3 | IC REG LDO 2.6V .15A SC75-6 |
| RMC19DRTF-S13 | CONN EDGECARD 38POS .100 EXTEND |
| ABC05DREF-S734 | CONN EDGECARD 10POS .100 EYELET |
| SIP21106DVP-25-E3 | IC REG LDO 2.5V .15A SC75-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX606EUA+ | 功能描述:直流/直流开关转换器 5V/12V or Adjustable Step-Up DC/DC Cnvrtr RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX606EUA+T | 功能描述:直流/直流开关转换器 5V/12V or Adjustable Step-Up DC/DC Cnvrtr RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX606EUA-T | 功能描述:直流/直流开关转换器 5V/12V or Adjustable Step-Up DC/DC Cnvrtr RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX606EVKIT | 功能描述:直流/直流开关转换器 Evaluation Kit for the MAX606 MAX607 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX606IUA | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Analog IC |
发布紧急采购，3分钟左右您将得到回复。