- 您现在的位置：买卖IC网 > PDF目录17028 > MAX613CSD (Maxim Integrated Products)IC PWR CNTRLR ANLG PCMCIA 14SOIC PDF资料下载
参数资料
| 型号： | MAX613CSD |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/8页 |
| 文件大小： | 0K |
| 描述： | IC PWR CNTRLR ANLG PCMCIA 14SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 类型： | PCMCIA/Cardbus 开关 |
| 输出数： | 2 |
| 内部开关： | 是 |
| 输入电压： | 2.85 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOIC |
| 包装： | 管件 |
Dual-Slot PCMCIA
Analog Power Controllers
VCC Switching
The MAX613/MAX614 contain level shifters that simplify
driving external power MOSFETs to switch PCMCIA card
Table 3. MAX613 DRV3 and DRV5 Control
– — — —
Logic ( S H D N = VCCIN)
VCC. While a PCMCIA card is being inserted into the
socket, the VCC pins on the card edge connector should
LOGIC INPUT
OUTPUT
be powered down to 0V to prevent “hot insertion” that
may damage the PCMCIA card. The MAX613/MAX614
MOSFET drivers are open drain. Their rise time is con-
trolled by an external pull-up resistor, allowing slow turn-
on of VCC power to the PCMCIA card.
The DRV3 and DRV5 pins on the MAX613 and the DRV
pin on the MAX614 are open-drain outputs pulled down
VCC1
0
0
1
1
VCC0
0
1
0
1
DRV3
0V
HI-Z
0V
0V
DRV5
0V
0V
HI-Z
0V
with internal N-channel devices. The gate drive to
these internal N-channel devices is powered from
VCCIN, regardless of VPPIN’s voltage. If VCCIN is left
unconnected or less than 2V is applied to VCCIN, the
DRV3/DRV5/DRV gate drivers will not sink current.
To switch VCC (M1 and M2 in Figure 1), use external
N-channel power MOSFETs. M1 and M2 should be
logic-level N-channel power MOSFETs with low on
resistance. The Motorola MTP3055EL and Siliconix
Si9956DY MOSFETs are both good choices. Turn on
M1 and M2 by pulling their gates above +5V. With the
gates pulled up to VPPIN as shown in Figure 1, VPPIN
should be at least 10V so that with VCC = 5.5V, M1 and
M2 have at least 4.5V of gate drive.
Table 1. AVPP Control Logic
The gates of M1 and M2 can be pulled up to any 10V to
20V source, and do not need to be pulled up to VPPIN.
Typically, the +12V used for VPPIN is supplied from a
+5V to +12V switching regulator. To save power, the
+5V to +12V switching regulator can be shut down
when not using the VPP programming voltage, allowing
VPPIN to fall below +5V.
In this case, M1 and M2 should not be pulled up to
VPPIN, since M1 and M2 cannot be turned on reliably
when VPPIN falls below +10V. Any clock source can
be used to generate a high-side gate-drive voltage by
using capacitors and diodes to build an inexpensive
charge pump. Figure 3 shows a charge-pump circuit
that generates 10V from a +5V logic clock source.
__________Applications Information
The MAX613 contains all the gate drivers and switch-
LOGIC INPUT
OUTPUT
ing circuitry needed to support a +3.3V/+5V VCC
PCMCIA slot with minimal external components.
AVPP1
0
0
1
1
AVPP0
0
1
0
1
AVPP
0V
VCCIN
VPPIN
HI-Z
Figure 4 shows the analog power control necessary to
support two dual voltage PCMCIA slots. The A:VCC
and B:VCC pins on the Intel 82365SL DF power the
drivers for the control signals that directly connect to
the PCMCIA card.
A 3.3V card needs 3.3V logic-level control signals and
the capability to program VPP1 and VPP2 to 3.3V. The
MAX613’s VCCIN is switched with slot VCC, so AVPP0
Table 2. BVPP Control Logic
= 1 and AVPP1 = 0 causes AVPP = slot VCC.
Likewise, A:VCC and B:VCC are connected to VCCIN,
LOGIC INPUT
OUTPUT
so the Intel 82365SL DF control signals to the PCMCIA
card are the right logic levels.
BVPP1
0
0
1
1
BVPP0
0
1
0
1
BVPP
0V
VCCIN
VPPIN
HI-Z
PCMCIA card interface controllers other than the
Intel 82365SL DF can be used with Figure 4 ’s cir-
cuit. Table 4 shows the pins on the Cirrus Logic
CL-PD6720 that perform the same function as the
Intel 82365SL DF pins.
6
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| 381LR151M400J022 | CAP ALUM 150UF 400V 20% SNAP |
| MAX1607ESA+ | IC SW USB CURRENT LIMIT 8SOIC |
| STD21W-D | WIRE & CABLE MARKERS |
| EEU-FR1C471B | CAP ALUM 470UF 16V 20% RADIAL |
| FPF2001 | IC SW LOAD FULL FUNC 50MA SC70-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX613CSD+T | 功能描述:接口 - 专用 RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MAX613CSD-T | 功能描述:接口 - 专用 RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MAX613EPD | 功能描述:接口 - 专用 RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MAX613ESD | 功能描述:接口 - 专用 RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MAX613ESD+ | 功能描述:接口 - 专用 RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
发布紧急采购，3分钟左右您将得到回复。