参数资料
型号: MAX6314US45D3+T
厂商: Maxim Integrated Products
文件页数: 6/8页
文件大小: 0K
描述: IC RESET CIRCUIT 4.50V SOT143-4
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 2,500
类型: 简单复位/加电复位
监视电压数目: 1
输出: 双向
复位: 低有效
复位超时: 最小为 140 ms
电压 - 阀值: 4.5V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: TO-253-4,TO-253AA
供应商设备封装: SOT-143-4
包装: 带卷 (TR)
68HC11/Bidirectional-Compatible
μP Reset Circuit
V CC
V CC
68HC11
4.7k ?
RESET
RESET
RESET
RESET
MR
CIRCUITRY
C IN
C STRAY
C IN
CIRCUITRY
MAX6314
RESET
Figure 2. MAX6314 Supports Additional Devices on the Reset Bus
C IN
OTHER DEVICES
MR has an internal 63k ? pullup resistor, so it can be
left open if not used. Connect a normally open momen-
tary switch from MR to GND to create a manual reset
function; external debounce circuitry is not required. If
MR is driven from long cables or if the device is used in
a noisy environment, connecting a 0.1μF capacitor from
MR to ground provides additional noise immunity.
__________Applications Information
Negative-Going V CC Transients
In addition to issuing a reset to the μP during power-up,
power-down, and brownout conditions, these devices
are relatively immune to short-duration negative-going
transients (glitches). The Typical Operating Character-
istics show the Maximum Transient Duration vs. Reset
Threshold Overdrive, for which reset pulses are not
generated. The graph was produced using negative-
going pulses, starting at V RST max and ending below
the programmed reset threshold by the magnitude
indicated (reset threshold overdrive). The graph shows
the maximum pulse width that a negative-going V CC
transient may typically have without causing a reset
pulse to be issued. As the amplitude of the transient
Ensuring a Valid RESET Output
Down to V CC = 0V
When V CC falls below 1V, RESET no longer sinks
current—it becomes an open circuit. Therefore, high-
impedance CMOS-logic inputs connected to RESET
can drift to undetermined voltages. This presents no
problem in most applications, since most μP and other
circuitry is inoperative with V CC below 1V. However, in
applications where RESET must be valid down to
V CC = 0V, adding a pull-down resistor to RESET will
cause any stray leakage currents to flow to ground,
holding RESET low (Figure 3). R1’s value is not critical;
100k ? is large enough not to load RESET and small
enough to pull RESET to ground.
V CC
MAX6314
RESET
increases (i.e., goes farther below the reset threshold),
the maximum allowable pulse width decreases. A 0.1μF
GND
R1
bypass capacitor mounted close to V CC provides addi-
tional transient immunity.
Figure 3. RESET Valid to V CC = Ground Circuit
6
_______________________________________________________________________________________
相关PDF资料
PDF描述
MAX6314US47D3+T IC RESET CIRCUIT 4.70V SOT143-4
MAX6314US45D2+T IC RESET CIRCUIT 4.50V SOT143-4
MAX6315US27D1+T IC RESET CIRCUIT 2.70V SOT143-4
TCG242U030L2L CAP ALUM 2400UF 30V AXIAL
MAX6315US27D4+T IC RESET CIRCUIT 2.70V SOT143-4
相关代理商/技术参数
参数描述
MAX6314US45D4 制造商:Maxim Integrated Products 功能描述:68HC11/BIDIRECTIONAL-COMPATIBLE UP - Rail/Tube
MAX6314US45D4+ 制造商:Maxim Integrated Products 功能描述:PROCESSOR SUPERVISOR 4.5V 5UA 4PIN SOT-143 - Rail/Tube
MAX6314US45D4+T 功能描述:监控电路 68HC11/Bidirectional Compatible uP Reset RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟(典型值):10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX6314US45D4-T 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟(典型值):10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX6314US46D1 制造商:Maxim Integrated Products 功能描述:68HC11/BIDIRECTIONAL-COMPATIBLE UP - Cut Tape Product