- 您现在的位置：买卖IC网 > PDF目录13690 > MAX6323CUT29+T (Maxim Integrated Products)IC SUPERVISOR 2.93V SOT23-6 PDF资料下载
参数资料
| 型号： | MAX6323CUT29+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 5/13页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR 2.93V SOT23-6 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 推挽式，图腾柱 |
| 复位： | 低有效 |
| 复位超时： | 最小为 100 ms |
| 电压 - 阀值： | 2.93V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-6 |
| 包装： | 带卷 (TR) |
μP Supervisory Circuits with Windowed
(Min/Max) Watchdog and Manual Reset
Typical Operating Characteristics (continued)
(V CC = full range, T A = +25°C, unless otherwise noted.)
FAST WATCHDOG TIMEOUT PERIOD
MAX6323/24-10
SLOW WATCHDOG TIMEOUT PERIOD
MAX6323/24-11
WDI
WDPO
MAX6323AUT23
500 μ s/div
2V/div
2V/div
WDI
WDPO
MAX6323AUT23
5ms/div
2V/div
2V/div
Pin Description
PIN
1
2
3
4
5
6
NAME
MR
GND
WDI
V CC
WDPO
RESET
FUNCTION
Active-Low, Manual Reset Input. When MR is asserted low, RESET is asserted low, the internal watchdog
timer is reset to zero, and WDPO is reset to high impedance (open drain). After the rising edge of MR ,
RESET is asserted for at least 100ms. Leave MR unconnected or connect to V CC if unused.
Ground
Watchdog Input. The internal watchdog timer clears to zero on the falling edge of WDI or when RESET goes
high. If WDI sees another falling edge within the factory-trimmed watchdog window, WDPO will remain
unasserted. Transitions outside this window, either faster or slower, will cause WDPO to pulse low for 1ms
(typ).
Supply Voltage for the Device. Input for V CC reset monitor. For noisy systems, bypass V CC with a 500pF
(min) capacitor.
Watchdog Pulse Output. The open-drain WDPO output is pulsed low for 1ms (typ) upon detection of a fast
or slow watchdog fault. WDPO is only active when RESET is high.
Active-Low. Reset is asserted when V CC drops below V TH and remains asserted until V CC rises above V TH
for the duration of the reset timeout period. The MAX6323 has a push-pull output and the MAX6324 has an
open-drain output. Connect a pullup resistor from RESET to any supply voltage up to +6V.
_______________________________________________________________________________________
5
相关PDF资料 |
PDF描述 |
|---|---|
| MAX709RCUA+ | IC SUPPLY MON W/RESET 8UMAX |
| RPP30-2424SW-1L | CONV DC/DC 30W 9-36VIN 24VOUT |
| MAX709SCUA+ | IC SUPPLY MON W/RESET 8UMAX |
| 4448-20L | TOROID POWER HI CURRENT 25UH SMD |
| MAX709LCUA+ | IC SUPPLY MON W/RESET 8UMAX |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6323CUT31 | 制造商:Maxim Integrated Products 功能描述:UP SUPERVISORY CIRCUIT WITH WINDOWE - Cut Tape Product |
| MAX6323CUT31+T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6323CUT31-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6323CUT44 | 制造商:Maxim Integrated Products 功能描述:UP SUPERVISORY CIRCUIT WITH WINDOWE - Cut Tape Product |
| MAX6323CUT44+T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。