- 您现在的位置：买卖IC网 > PDF目录13779 > MAX6356TWUT+T (Maxim Integrated Products)IC SUPERVISOR MPU SOT23-6 PDF资料下载
参数资料
| 型号： | MAX6356TWUT+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 8/11页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR MPU SOT23-6 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 多压监控器 |
| 监视电压数目： | 3 |
| 输出： | 推挽式，图腾柱 |
| 复位： | 低有效 |
| 复位超时： | 最小为 100 ms |
| 电压 - 阀值： | 1.67V，3.08V，可调 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-6 |
| 包装： | 带卷 (TR) |
Dual/Triple-Voltage
μP Supervisory Circuits
During the normal operating mode, the supervisor will
issue a reset pulse for the reset timeout period (140ms
min) if the μP does not update the WDI with a valid tran-
V CC 2
V CC 1
sition (HIGH to LOW or LOW to HIGH) within the stan-
dard timeout period (1.6s min).
After each reset event (V CC power-up, manual reset, or
watchdog reset), there is an initial watchdog startup
V CC 1
V CC 2
RST
RST2
RST1
100k ?
timeout period of 25.6s. The startup mode provides an
extended period for the system to power up and fully
initialize all μP and system components before assum-
ing responsibility for routine watchdog updates. The
normal watchdog timeout period (1.6s min) begins at
the conclusion of the startup timeout period or after the
first transition on WDI before the conclusion of the start-
up period (Figure 3).
Applications Information
Ensuring a Valid RESET Output
Down to V CC = 0
In some systems, it is necessary to ensure a valid reset
even if V CC falls to 0. In these applications, use the cir-
cuit shown in Figure 4. Note that this configuration does
not work for the open-drain outputs of the MAX6352/
MAX6355/MAX6358.
MAX6351 MAX6356
MAX6353 MAX6357
MAX6354 MAX6359
MAX6360
GND
Figure 4. Ensuring a Valid Reset Low to V CC 1 and V CC 2 = 0
BUFFERED RESET TO OTHER SYSTEM COMPONENTS
V CC 2 V CC 1
Interfacing to μPs with
Bidirectional Reset Pins
Microprocessors with bidirectional reset pins will con-
tend with the push-pull outputs of these devices. To
prevent this, connect a 4.7k ? resistor between RESET
V CC 1
V CC 2
RST
RST2
RST1
4.7k ?
RESET
μ P
and the μP’s reset I/O port, as shown in Figure 5. Buffer
RESET as shown in the figure if this reset is used by
MAX6351–MAX6360
GND
other components in the system.
V TH
GND
Figure 5. Interfacing to μPs with Bidirectional Reset I/O
V CC
t WDI-NORMAL
1.6s MAX
WDI
t WDI-STARTUP
25.6s MAX
1.6s
MAX
TRANSISTOR COUNT: 855
Chip Information
RESET
140ms
Figure 3. Normal Watchdog Startup Sequence
8
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| 200LLE8.2MEFCT78X9 | CAP ALUM 8.2UF 200V 20% RADIAL |
| VI-21P-EX-F1 | CONVERTER MOD DC/DC 13.8V 75W |
| SCMS5D14-101 | INDUCTOR SMD 100UH 0.35A 100KHZ |
| VE-J6Y-EZ-F4 | CONVERTER MOD DC/DC 3.3V 16.5W |
| MAX6356SWUT+T | IC SUPERVISOR MPU SOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6356TYUK-T | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Dual/Triple-Voltage レP Supervisory Circuits |
| MAX6356TYUT | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX6356TYUT+T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6356TYUT-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6356TZUT | 制造商:Maxim Integrated Products 功能描述:6 PINS THNSOT PKG - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。