- 您现在的位置：买卖IC网 > PDF目录14804 > MAX6423US33+T (Maxim Integrated Products)IC MPU/RESET CIRC 3.30V SOT143-4 PDF资料下载
参数资料
| 型号： | MAX6423US33+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 5/10页 |
| 文件大小： | 0K |
| 描述： | IC MPU/RESET CIRC 3.30V SOT143-4 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 3.3V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | TO-253-4，TO-253AA |
| 供应商设备封装： | SOT-143-4 |
| 包装： | 带卷 (TR) |
Low-Power, SC70/SOT μP Reset Circuits with
Capacitor-Adjustable Reset Timeout Delay
C SRT = (t RP - 275μs) / (2.73 ? 10 6 )
where t RP is in seconds and C SRT is in farads.
The reset delay time is set by a current/capacitor-con-
trolled ramp compared to an internal 0.65V reference.
An internal 240nA ramp current source charges the
external capacitor. The charge to the capacitor is
cleared when a reset condition is detected. Once the
reset condition is removed, the voltage on the capacitor
ramps according to the formula: dV/dt = I/C. The C SRT
capacitor must ramp to 0.65V to deassert the reset.
C SRT must be a low-leakage (<10nA) type capacitor;
ceramic is recommended.
Operating as a Voltage Detector
The MAX6340/MAX6421–MAX6426 can be operated in a
voltage detector mode by floating the SRT pin. The reset
delay times for V CC rising above or falling below the
threshold are not significantly different. The reset output is
deasserted smoothly without false pulses.
V CC
V DD
Applications Information
Interfacing to Other Voltages for Logic
Compatibility
The open-drain outputs of the MAX6340/MAX6423/
MAX6425/MAX6426 can be used to interface to μPs with
other logic levels. As shown in Figure 1, the open-drain
output can be connected to voltages from 0 to 5.5V. This
allows for easy logic compatibility to various μPs.
Wired-OR Reset
To allow auxiliary circuitry to hold the system in reset,
an external open-drain logic signal can be connected
to the open-drain RESET of the MAX6340/MAX6423/
MAX6425/MAX6426, as shown in Figure 2. This config-
uration can reset the μP, but does not provide the reset
timeout when the external logic signal is released.
Negative-Going V CC Transients
In addition to issuing a reset to the μP during power-up,
power-down, and brownout conditions, these supervisors
are relatively immune to short-duration negative-going
transients (glitches). The graph Maximum Transient
Duration vs. Reset Threshold Overdrive in the Typical
Operating Characteristics shows this relationship.
The area below the curve of the graph is the region in
which these devices typically do not generate a reset
pulse. This graph was generated using a negative-
going pulse applied to V CC , starting above the actual
reset threshold (V TH ) and ending below it by the magni-
tude indicated (reset-threshold overdrive). As the mag-
nitude of the transient decreases (farther below the
MAX6340
MAX6423
MAX6425
MAX6426
RESET
N
GND
OPEN-DRAIN
LOGIC
N
Figure 2. Wired-OR Reset Circuit
10k ?
μ P
RESET
reset threshold), the maximum allowable pulse width
decreases. Typically, a V CC transient that goes 100mV
below the reset threshold and lasts 50μs or less does
not cause a reset pulse to be issued.
Ensuring a Valid RESET or RESET
Down to V CC = 0
When V CC falls below 1V, RESET /RESET current-sink-
ing (sourcing) capabilities decline drastically. In the
case of the MAX6421/MAX6424, high-impedance
CMOS-logic inputs connected to RESET can drift to
undetermined voltages. This presents no problems in
most applications, since most μPs and other circuitry
do not operate with V CC below 1V.
In those applications where RESET must be valid down
to zero, adding a pulldown resistor between RESET
and ground sinks any stray leakage currents, holding
RESET low (Figure 3). The value of the pulldown resis-
tor is not critical; 100k ? is large enough not to load
RESET and small enough to pull RESET to ground. For
applications using the MAX6422, a 100k ? pullup resis-
_______________________________________________________________________________________
5
相关PDF资料 |
PDF描述 |
|---|---|
| CDR125NP-470MC | POWER INDUCTOR 47UH 1.50A SMD |
| ESC12DTEI | CONN EDGECARD 24POS .100 EYELET |
| V110B5T100B2 | CONVERTER MOD DC/DC 5V 100W |
| CDR125NP-391MC | POWER INDUCTOR 390UH 0.52A SMD |
| ECC40DRXI | CONN EDGECARD 80POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6423US34 | 制造商:Maxim Integrated Products 功能描述:LOW-POWER SC70/SOT MICROPROCESSOR - Rail/Tube |
| MAX6423US34+ | 制造商:Maxim Integrated Products 功能描述:PROCESSOR SUPERVISOR 3.4V 2.5UA 4PIN SOT-143 - Rail/Tube |
| MAX6423US34+T | 功能描述:监控电路 Single uPower Reset Circuit RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6423US34-T | 功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX6423US35 | 制造商:Maxim Integrated Products 功能描述:LOW-POWER SC70/SOT MICROPROCESSOR - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。