- 您现在的位置：买卖IC网 > PDF目录61653 > MAX6501UKP065+T (MAXIM INTEGRATED PRODUCTS INC) Low-Cost, +2.7V to +5.5V, Micropower Temperature Switches in SOT23 and TO-220 PDF资料下载
参数资料
| 型号： | MAX6501UKP065+T |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | Low-Cost, +2.7V to +5.5V, Micropower Temperature Switches in SOT23 and TO-220 |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO5 |
| 封装： | ROHS COMPLIANT, MO-178AA, SOT-23, 5 PIN |
| 文件页数： | 6/9页 |
| 文件大小： | 289K |
| 代理商： | MAX6501UKP065+T |
MAX6501–MAX6504
Low-Cost, +2.7V to +5.5V, Micropower
Temperature Switches in SOT23
6
_______________________________________________________________________________________
Applications Information
Thermal Considerations
The MAX6501–MAX6504 supply current is typically
30A. When used to drive high-impedance loads, the
devices dissipate negligible power. Therefore, the die
temperature is essentially the same as the package
temperature. The key to accurate temperature monitor-
ing is good thermal contact between the MAX6501–
MAX6504 package and the device being monitored. In
some applications, the SOT23 package may be small
enough to fit underneath a socketed P, allowing the
device to monitor the P’s temperature directly. Use the
monitor’s output to reset the P, assert an interrupt, or
trigger an external alarm.
Accurate temperature monitoring depends on the ther-
mal resistance between the device being monitored
and the MAX6501–MAX6504 die. Heat flows in and out
of plastic packages, primarily through the leads. Pin 2
of the SOT23-5 package provides the lowest thermal
resistance to the die. Short, wide copper traces leading
to the temperature monitor ensure that heat transfers
quickly and reliably.
The rise in die temperature due to self-heating is given
by the following formula:
ΔTJ = PDISSIPATION x θJA
where PDISSIPATION is the power dissipated by the
MAX6501–MAX6504, and
θJA is the package’s thermal
resistance.
The typical thermal resistance is 140°C/W for the
SOT23 package. To limit the effects of self-heating,
minimize the output currents. For example, if the
MAX6501 or MAX6503 sink 1mA, the output voltage is
guaranteed to be less than 0.3V. Therefore, an addi-
tional 0.3mW of power is dissipated within the IC. This
corresponds to a 0.042°C shift in the die temperature in
the SOT23.
Temperature-Window Alarm
The MAX6501–MAX6504 temperature switch outputs
assert when the die temperature is outside the factory-
programmed range. Combining the outputs of two
devices creates an over/undertemperature alarm. The
MAX6501/MAX6503 and the MAX6502/MAX6504 are
designed to form two complementary pairs, each con-
taining one cold trip-point output and one hot trip-point
output. The assertion of either output alerts the system to
an out-of-range temperature. The MAX6502/MAX6504
push/pull output stages can be ORed to produce a ther-
mal out-of-range alarm. More favorably, a MAX6501/
MAX6503 can be directly wire-ORed with a single exter-
nal resistor to accomplish the same task (Figure 4).
The temperature window alarms shown in Figure 4 can
be used to accurately determine when a device’s tem-
perature falls out of the -5°C to +75°C range. The ther-
mal-overrange signal can be used to assert a thermal
shutdown, power-up, recalibration, or other temperature-
dependent function.
Low-Cost, Fail-Safe
Temperature Monitor
In high-performance/high-reliability applications, multi-
ple temperature monitoring is important. The high-level
integration and low cost of the MAX6501–MAX6504
facilitate the use of multiple temperature monitors to in-
crease system reliability. Figure 5’s application uses
two MAX6502s with different temperature thresholds to
ensure that fault conditions that can overheat the moni-
tored device cause no permanent damage. The first
temperature monitor activates the fan when the die
temperature exceeds +45°C. The second MAX6502
triggers a system shutdown if the die temperature
reaches +75°C. The second temperature monitor’s out-
put asserts when a wide variety of destructive fault con-
ditions occur, including latchups, short circuits, and
cooling-system failures.
MAX6502
+5V
TOVER
GND
VCC
HYST
μP
FAN
HEAT
VCC
Figure 3. Overtemperature Fan Control
MAX6501
+3.3V
GND
HYST
GND
VCC
μP
HEAT
VCC
RPULLUP
100k
Ω
TOVER
INT
SHUTDOWN
OR
RESET
Figure 2. Microprocessor Alarm/Reset
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6502UKP065+T | Low-Cost, +2.7V to +5.5V, Micropower Temperature Switches in SOT23 and TO-220 |
| MAX6502UKP125+T | Low-Cost, +2.7V to +5.5V, Micropower Temperature Switches in SOT23 and TO-220 |
| MAX6505UTN005+T | Dual Trip SOT Temperature Switches |
| MAX6505UTN010+T | Dual Trip SOT Temperature Switches |
| MAX6505UTN015+T | Dual Trip SOT Temperature Switches |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6501UKP075 | 制造商:Maxim Integrated Products 功能描述:LOW-COST +2.7V TO +5.5V MICROPOWER TEMPERATURE SWITCHES IN S - Rail/Tube 制造商:Rochester Electronics LLC 功能描述: |
| MAX6501UKP075+ | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR ANLG 5PIN SOT-23 - Rail/Tube |
| MAX6501UKP075+T | 功能描述:板上安装温度传感器 2.7-5.5V uPower Temperature Switch RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6501UKP075-T | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6501UKP085 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。