- 您现在的位置：买卖IC网 > PDF目录19499 > MAX6627MTA+T (Maxim Integrated)IC TEMP SENSOR DGTL 8-TDFN PDF资料下载
参数资料
| 型号： | MAX6627MTA+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 7/9页 |
| 文件大小： | 257K |
| 描述： | IC TEMP SENSOR DGTL 8-TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 功能： | 温度监控系统（传感器） |
| 传感器类型： | 外部 |
| 感应温度： | -55°C ~ 145°C |
| 精确度： | ±2.4°C（最小值） |
| 拓扑： | ADC |
| 输出类型： | 3 线/SPI? 串行 |
| 输出警报： | 无 |
| 输出风扇： | 无 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WDFN 裸露焊盘 |
| 供应商设备封装： | 8-TDFN-EP（2x2） |
| 包装： | 标准包装 |
| 产品目录页面： | 1425 (CN2011-ZH PDF) |
| 其它名称： | MAX6627MTA+TDKR |
Filter high-frequency electromagnetic interference
(EMI) at DXP and DXN with an external 2200pF capaci-
tor connected between the two inputs. This capacitor
can be increased to about 3300pF (max), including
cable capacitance. A capacitance higher than 3300pF
introduces errors due to the rise time of the switched-
current source.
PCB Layout
1) Place the MAX6627/MAX6628 as close as practical
to the remote diode. In a noisy environment, such
as a computer motherboard, this distance can be
4in to 8in, or more, as long as the worst noise
sources (such as CRTs, clock generators, memory
buses, and ISA/PCI buses) are avoided.
2) Do not route the DXP/DXN lines next to the deflec-
tion coils of a CRT. Also, do not route the traces
across a fast memory bus, which can easily intro-
duce +30癈 error, even with good filtering.
Otherwise, most noise sources are fairly benign.
3) Route the DXP and DXN traces parallel and close to
each other, away from any high-voltage traces such
as +12VDC. Avoid leakage currents from PCB cont-
amination. A 20M?leakage path from DXP to
ground causes approximately +1癈 error.
4) Connect guard traces to GND on either side of the
DXP/DXN traces (Figure 3). With guard traces in
place, routing near high-voltage traces is no longer
an issue.
5) Route as few vias and crossunders as possible to
minimize copper/solder thermocouple effects.
6) When introducing a thermocouple, make sure that
both the DXP and the DXN paths have matching
thermocouples. In general, PCB-induced thermo-
couples are not a serious problem. A copper solder
thermocouple exhibits 3礦/癈, and it takes approxi-
mately 200礦 of voltage error at DXP/DXN to cause
a +1癈 measurement error, so most parasitic ther-
mocouple errors are swamped out.
7) Use wide traces. Narrow traces are more inductive
and tend to pick up radiated noise. The 10mil
widths and spacings recommended in Figure 3 are
not absolutely necessary (as they offer only a minor
improvement in leakage and noise), but use them
where practical.
8) Placing an electrically clean copper ground plane
between the DXP/DXN traces and traces carrying
high-frequency noise signals helps reduce EMI.
Twisted Pair and Shielded Cables
For remote-sensor distances longer than 8in, or in par-
ticularly noisy environments, a twisted pair is recom-
mended. Its practical length is 6ft to 12ft (typ) before
noise becomes a problem, as tested in a noisy elec-
tronics laboratory. For longer distances, the best solu-
tion is a shielded twisted pair like that used for audio
microphones. For example, Belden #8451 works well
for distances up to 100ft in a noisy environment.
Connect the twisted pair to DXP and DXN and the
shield to ground, and leave the shields remote end
unterminated. Excess capacitance at DXN or DXP limits
practical remote-sensor distances (see Typical
Operating Characteristics).
For very long cable runs, the cables parasitic capaci-
tance often provides noise filtering, so the recommend-
ed 2200pF capacitor can often be removed or reduced
in value. Cable resistance also affects remote-sensor
accuracy. A 1?series resistance introduces about
+1/2癈 error.
Remote ?癈 Accurate Digital Temperature
Sensors with SPI-Compatible Serial Interface
_______________________________________________________________________________________ 7
MINIMUM
10mils
10mils
10mils
10mils
GND
DXN
DXP
GND
Figure 3. Recommended DXP/DXN PC Traces
相关PDF资料 |
PDF描述 |
|---|---|
| TAJB106M016HNJ | CAP TANT 10UF 16V 20% 1210 |
| LT3015IT#TRPBF | IC REG LDO NEG ADJ 1.5A 5-TO220 |
| VE-B0Z-CX-F4 | CONVERTER MOD DC/DC 2V 30W |
| LT3015ET#TRPBF | IC REG LDO NEG ADJ 1.5A 5-TO220 |
| TAP155M050BRW | CAP TANT 1.5UF 50V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6628MKA | 制造商:Maxim Integrated Products 功能描述:REMOTE +/- 1-DEGREE C ACCURATE DIGITAL TEMPER - Bulk |
| MAX6628MKA+ | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 3-WIRE/SPI 8PIN SOT-23 - Rail/Tube |
| MAX6628MKA+T | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 3-WIRE/SPI 8PIN SOT-23 - Tape and Reel |
| MAX6628MKA-T | 功能描述:板上安装温度传感器 1C Accurate Temperature Sensor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6628MTA+ | 制造商:Maxim Integrated Products 功能描述:REMOTE ?1?C ACCURATE DIGITAL TEMPERATURE SENSORS WITH SPI - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。