参数资料
型号: MAX6629EVKIT
厂商: Maxim Integrated Products
文件页数: 6/8页
文件大小: 0K
描述: EVAL KIT FOR MAX6629
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 1
传感器类型: 温度
传感范围: -55°C ~ 150°C
接口: SPI 3 线串行
灵敏度: ±0.2°C
电源电压: 3 V ~ 5.5 V
嵌入式:
已供物品: 板,CD
已用 IC / 零件: MAX6629
12-Bit + Sign Digital Temperature Sensors
with Serial Interface
t CSS
CS
SCK
SO
t DV
t DO
t TR
D15
D3
D2
D1
D0
Figure 3. SPI Timing Diagram
Table 1. Data Output Format
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
Sign
MSB
Data
LSB
Data
Low
High-Z
High-Z
Table 2. Temperature Data Format
(Two’s Complement)
undefined and are always in high-impedance mode
(Table 1). The power-up state for SO is high imped-
ance. Figure 3 shows the detailed serial timing specifi-
TEMPERATURE
(°C)
DIGITAL OUTPUT (BINARY)
D15–D3 D2 D1, D0
cations for the SPI port. The temperature data format is
in two's complement format (Table 2).
150
125
25
0.0625
0
-0.0625
-25
-55
0,1001,0110,0000
0,0111,1101,0000
0,0001,1001,0000
0,0000,0000,0001
0,0000,0000,0000
1,1111,1111,1111
1,1110,0111,0000
1,1100,1001,0000
0
0
0
0
0
0
0
0
XX
XX
XX
XX
XX
XX
XX
XX
Power Shutdown Mode
The MAX6629–MAX6632 do not have a built-in power
software shutdown mode. However, a power shutdown
mode is easily implemented utilizing an unused logic
gate. A typical CMOS or TTL logic output has enough
drive capability to serve as the power source if its out-
put voltage level exceeds 3V, as shown in Figure 1.
Drive the logic output low to provide a hardware shut-
down mode.
Idle Mode
finish. CS ’s falling edge stops any conversion in
progress, and data is latched into the shift register.
Then the data clocks out at SO on SCK’s falling edge
with the sign bit (D15) first, followed by the MSB. Data
is sent in one 16-bit word, and CS must remain low until
all 16 bits are transferred. If CS goes high in the middle
of a transmission, it is necessary to wait the conversion
time (less than 300ms) before attempting a new read.
The serial data is composed of 12 + 1 data bits
(D15–D3) and 3 trailing bits (D2–D0). D2 is always low,
serving as the confirmation bit that the device has been
communicated with. The last 2 bits, D0 and D1, are
The MAX6629–MAX6632 can be put into idle mode by
pulling CS low. Data can be clocked out when the
device is in idle mode.
Power-On Reset (POR)
The POR supply voltage of the MAX6629–MAX6632 is
typically 1.6V. Below this supply voltage, the interface
is inactive and the data register is set to the POR state,
0°C.
When power is first applied and V CC rises above 1.6V
(typ), the device starts to convert, although temperature
reading is not recommended at V CC levels below 3.0V.
6
_______________________________________________________________________________________
相关PDF资料
PDF描述
MAX6635EVKIT+ EVALUATION KIT FOR MAX6635
MAX6639EVKIT+ EVALUATION KIT FOR MAX6639/F
MAX6654EVKIT EVAL KIT FOR MAX6654
MAX6655EVSYS EVAL KIT FOR MAX6655
MAX6660EVKIT EVAL KIT FOR MAX6660
相关代理商/技术参数
参数描述
MAX6629MTT+ 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 3-WIRE/SPI 6TDFN EP - Rail/Tube
MAX6629MTT+T 功能描述:板上安装温度传感器 12-Bit + Sign Temperature Sensor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
MAX6629MUT 制造商:Maxim Integrated Products 功能描述:12-BIT + SIGN DIGITAL TEMPERATURE SENSORS WIT - Rail/Tube
MAX6629MUT#G16 制造商:Maxim Integrated Products 功能描述:12-BIT + SIGN DIGITAL TEMPERATURE SENSORS WITH SERIAL INTERF - Rail/Tube
MAX6629MUT#TG16 功能描述:板上安装温度传感器 12-Bit + Sign Temperature Sensor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor