- 您现在的位置：买卖IC网 > PDF目录67800 > MAX6639AEE+ (MAXIM INTEGRATED PRODUCTS INC) 2-Channel Temperature Monitor with Dual, Automatic, PWM Fan-Speed Controller PDF资料下载
参数资料
| 型号： | MAX6639AEE+ |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | 2-Channel Temperature Monitor with Dual, Automatic, PWM Fan-Speed Controller |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| 封装： | QSOP-16 |
| 文件页数： | 13/22页 |
| 文件大小： | 189K |
| 代理商： | MAX6639AEE+ |
MAX6639/MAX6639F
3) Route the DXP and DXN traces parallel and close to
each other, away from any high-voltage traces such
as +12VDC. Avoid leakage currents from PCB cont-
amination. A 20M
Ω leakage path from DXP ground
causes approximately +1°C error.
4) Connect guard traces to GND on either side of the
DXP/DXN traces. With guard traces, placing routing
near high-voltage traces is no longer an issue.
5) Route as few vias and crossunders as possible to
minimize copper/solder thermocouple effects.
6) When introducing a thermocouple, make sure that
both the DXP and the DXN paths have matching
thermocouples. In general, PCB-induced thermo-
couples are not a serious problem. A copper solder
thermocouple exhibits 3V/°C, and it takes approxi-
mately 200V of voltage error at DXP/DXN to cause
a +1°C measurement error, so most parasitic ther-
mocouple errors are swamped out.
7) Use wide traces. Narrow traces are more inductive
and tend to pick up radiated noise. The 10-mil widths
and spacings recommended are not absolutely nec-
essary (as they offer only a minor improvement in
leakage and noise), but use them where practical.
8) Placing an electrically clean copper ground plane
between the DXP/DXN traces and traces carrying
high-frequency noise signals helps reduce EMI.
2-Channel Temperature Monitor with Dual,
Automatic, PWM Fan-Speed Controller
20
______________________________________________________________________________________
MAX6639
VFAN
(5V OR 12V)
SDA
SCL
PWM2
DXP1
DXN
TO CLOCK THROTTLE
TO SYSTEM SHUTDOWN
TO SMBus
MASTER
3.3V TO 5.5V
3.0V TO 3.6V
3.3V TO 5.5V
PWM1
5V
DXP2
GPU
VCC
CPU
GND
5V
TACH1
ADD
TACH2
ALERT
THERM
FANFAIL
VFAN
(5V OR 12V)
OT
Typical Operating Circuit
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6639FAEE+ | 2-Channel Temperature Monitor with Dual, Automatic, PWM Fan-Speed Controller |
| MAX6640AEE+T | 2-Channel Temperature Monitor with Dual Automatic PWM Fan-Speed Controller |
| MAX6640YAEE+ | 2-Channel Temperature Monitor with Dual Automatic PWM Fan-Speed Controller |
| MAX6640YAEE+T | 2-Channel Temperature Monitor with Dual Automatic PWM Fan-Speed Controller |
| MAX6640AEE+ | 2-Channel Temperature Monitor with Dual Automatic PWM Fan-Speed Controller |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6639AEE+ | 功能描述:板上安装温度传感器 2Ch Temperature Monitor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6639AEE+T | 功能描述:板上安装温度传感器 2Ch Temperature Monitor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6639AEE-T | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MAX6639ATE | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MAX6639ATE+ | 功能描述:板上安装温度传感器 2Ch Temperature Monitor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。