- 您现在的位置：买卖IC网 > PDF目录67800 > MAX6639AEE+T (MAXIM INTEGRATED PRODUCTS INC) 2-Channel Temperature Monitor with Dual, Automatic, PWM Fan-Speed Controller PDF资料下载
参数资料
| 型号： | MAX6639AEE+T |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | 2-Channel Temperature Monitor with Dual, Automatic, PWM Fan-Speed Controller |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| 封装： | 0.150 INCH, 0.025 INCH PITCH, ROHS COMPLIANT, MO-137AB, QSOP-16 |
| 文件页数： | 11/24页 |
| 文件大小： | 393K |
| 代理商： | MAX6639AEE+T |
Effect of Series Resistance
Series resistance in a sense diode contributes addition-
al errors. For nominal diode currents of 10A and
100A, change in the measured voltage is:
VM = RS (100A - 10A) = 90A x RS
Since 1°C corresponds to 198.6V, series resistance
contributes a temperature offset of:
Assume that the diode being measured has a series
resistance of 3
. The series resistance contributes an
offset of:
The effects of the ideality factor and series resistance
are additive. If the diode has an ideality factor of 1.002
and series resistance of 3
, the total offset can be cal-
culated by adding error due to series resistance with
error due to ideality factor:
1.36°C - 2.13°C = -0.77°C
for a diode temperature of +85°C.
In this example, the effect of the series resistance and
the ideality factor partially cancel each other.
For best accuracy, the discrete transistor should be a
small-signal device with its collector connected to GND
and base connected to DXN. Table 12 lists examples of
discrete transistors that are appropriate for use with the
MAX6639.
The transistor must be a small-signal type with a rela-
tively high forward voltage; otherwise, the ADC input
voltage range can be violated. The forward voltage at
the highest expected temperature must be greater than
0.25V at 10A, and at the lowest expected tempera-
ture, the forward voltage must be less than 0.95V at
100A. Large-power transistors must not be used. Also,
ensure that the base resistance is less than 100
. Tight
specifications for forward current gain (50 < < 150,
for example) indicate that the manufacturer has good
process controls and that the devices have consistent
VBE characteristics.
ADC Noise Filtering
The integrating ADC has inherently good noise rejec-
tion, especially of low-frequency signals such as
60Hz/120Hz power-supply hum. Micropower operation
places constraints on high-frequency noise rejection.
Lay out the PC board carefully with proper external
noise filtering for high-accuracy remote measurements
in electrically noisy environments.
Filter high-frequency electromagnetic interference
(EMI) at DXP and DXN with an external 2200pF capaci-
tor connected between the two inputs. This capacitor
can be increased to approximately 3300pF (max),
including cable capacitance. A capacitance higher
than 3300pF introduces errors due to the rise time of
the switched-current source.
Twisted Pairs and Shielded Cables
For remote-sensor distances longer than 8in, or in par-
ticularly noisy environments, a twisted pair is recom-
mended. Its practical length is 6ft to 12ft (typ) before
noise becomes a problem, as tested in a noisy elec-
tronics laboratory. For longer distances, the best solu-
tion is a shielded twisted pair like that used for audio
microphones. For example, Belden #8451 works well
for distances up to 100ft in a noisy environment.
Connect the twisted pair to DXP and DXN and the
shield to ground, and leave the shield’s remote end
unterminated. Excess capacitance at DXN or DXP limits
practical remote-sensor distances (see the Typical
Operating Characteristics).
For very long cable runs, the cable’s parasitic capaci-
tance often provides noise filtering, so the recommend-
ed 2200pF capacitor can often be removed or reduced
in value. Cable resistance also affects remote-sensor
accuracy. A 1
series resistance introduces about
+1/2°C error.
PC Board Layout Checklist
1) Place the MAX6639 as close as practical to the
remote diode. In a noisy environment, such as a
computer motherboard, this distance can be 4in to
8in, or more, as long as the worst noise sources
(such as CRTs, clock generators, memory buses,
and ISA/PCI buses) are avoided.
2) Do not route the DXP/DXN lines next to the deflection
coils of a CRT. Also, do not route the traces across a
fast memory bus, which can easily introduce +30°C
error, even with good filtering. Otherwise, most noise
sources are fairly benign.
3) Route the DXP and DXN traces parallel and close to
each other, away from any high-voltage traces such
as +12VDC. Avoid leakage currents from PC board
contamination. A 20M
leakage path from DXP
ground causes approximately +1°C error.
4) Connect guard traces to GND on either side of the
DXP/DXN traces. With guard traces, placing routing
3
0 453
1 36
×
°
=°
.
C
90
198 6
0 453
°
=
°
V
C
.
MAX6639
2-Channel Temperature Monitor with Dual,
Automatic, PWM Fan-Speed Controller
______________________________________________________________________________________
19
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6639ATE+ | 2-Channel Temperature Monitor with Dual, Automatic, PWM Fan-Speed Controller |
| MAX6639ATE+T | 2-Channel Temperature Monitor with Dual, Automatic, PWM Fan-Speed Controller |
| MAX6639YAEE+ | 2-Channel Temperature Monitor with Dual, Automatic, PWM Fan-Speed Controller |
| MAX6639YAEE+T | 2-Channel Temperature Monitor with Dual, Automatic, PWM Fan-Speed Controller |
| MAX6639AEE+ | 2-Channel Temperature Monitor with Dual, Automatic, PWM Fan-Speed Controller |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6639ATE | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MAX6639ATE+ | 功能描述:板上安装温度传感器 2Ch Temperature Monitor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6639ATE+T | 功能描述:板上安装温度传感器 2Ch Temperature Monitor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6639ATE-T | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MAX6639EVKIT+ | 功能描述:马达/运动/点火控制器和驱动器 MAX6639/39F Eval Kit RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。