- 您现在的位置：买卖IC网 > PDF目录67800 > MAX6642ATT92+T (MAXIM INTEGRATED PRODUCTS INC) ±1°C, SMBus-Compatible Remote/Local Temperature Sensor with Overtemperature Alarm PDF资料下载
参数资料
| 型号： | MAX6642ATT92+T |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 温度/湿度传感器 |
| 英文描述： | ±1°C, SMBus-Compatible Remote/Local Temperature Sensor with Overtemperature Alarm |
| 中文描述： | DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 1Cel, SQUARE, SURFACE MOUNT |
| 封装： | 3 X 3 MM, 0.80 MM HEIGHT, MO-229WEEA, TDFN-6 |
| 文件页数： | 12/14页 |
| 文件大小： | 213K |
| 代理商： | MAX6642ATT92+T |
register was previously selected by a Write Byte
instruction. Use caution when using the shorter proto-
cols in multimaster systems, as a second master could
overwrite the command byte without informing the first
master.
Read temperature data from the read internal tempera-
ture (00h) and read external temperature (01h) regis-
ters. The temperature data format for these registers is
8 bits for each channel, with the LSB representing +1°C
(Table 1).
Read the additional bits from the read extended tem-
perature byte register (10h, 11h), which extends the
data to 10 bits and the resolution to +0.25
°C per LSB
(Table 2).
When a conversion is complete, the main temperature
register and the extended temperature register are
updated.
Alarm Threshold Registers
Two registers store ALERT threshold values—one each
for the local and remote channels. If either measured
temperature equals or exceeds the corresponding
ALERT threshold value, the ALERT interrupt asserts
unless the ALERT bit is masked.
The power-on-reset (POR) state of the local ALERT
THIGH register is +70
°C (0100 0110). The POR state of
the remote ALERT THIGH register is +120
°C (0111 1000).
Diode Fault Detection
A continuity fault detector at DXP detects an open cir-
cuit on DXP, or a DXP short to VCC or GND. If an open
or short circuit exists, the external temperature register
is loaded with 1111 1111 and status bit 2 (OPEN) of the
status byte is set to 1. Immediately after POR, the status
register indicates that no fault is present. If a fault is
present upon power-up, the fault is not indicated until
the end of the first conversion. Diode faults do not set
the ALERT output.
ALERT Interrupts
The ALERT interrupt occurs when the internal or external
temperature reading exceeds a high temperature limit
(user programmed). The ALERT interrupt output signal is
latched and can be cleared only by reading the status
register after the fault condition no longer exists or by
successfully responding to the alert response address. If
MAX6642
±1°C, SMBus-Compatible Remote/Local
Temperature Sensor with Overtemperature Alarm
_______________________________________________________________________________________
7
SMBCLK
AB
C
D
E
FG
H
I
SMBDATA
tSU:STA
tHD:STA
tLOW
tHIGH
tSU:DAT
tHD:DAT
tSU:STO tBUF
A = START CONDITION
B = MSB OF ADDRESS CLOCKED INTO SLAVE
C = LSB OF ADDRESS CLOCKED INTO SLAVE
D = R/W BIT CLOCKED INTO SLAVE
E = SLAVE PULLS SMBDATA LINE LOW
J
K
F = ACKNOWLEDGE BIT CLOCKED INTO MASTER
G = MSB OF DATA CLOCKED INTO MASTER
H = LSB OF DATA CLOCKED INTO MASTER
I = ACKNOWLEDGE CLOCK PULSE
J = STOP CONDITION
K = NEW START CONDITION
Figure 3. SMBus Read Timing Diagram
TEMP (
°C)
DIGITAL OUTPUT
130.00
1 000 0010
127.00
0 111 1111
126.00
0 111 1110
25
0 001 1001
0.00
0 000 0000
<0.00
0 000 0000
Diode fault (short or open)
1 111 1111
Table 1. Main Temperature Register
(High Byte) Data Format
FRACTIONAL TEMP (°C)
DIGITAL OUTPUT
0.000
00XX XXXX
0.250
01XX XXXX
0.500
10XX XXXX
0.750
11XX XXXX
Table 2. Extended Resolution
Temperature Register (Low Byte) Data
Format
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6642ATT94+T | ±1°C, SMBus-Compatible Remote/Local Temperature Sensor with Overtemperature Alarm |
| MAX6642ATT98+T | ±1°C, SMBus-Compatible Remote/Local Temperature Sensor with Overtemperature Alarm |
| MAX6642YATT98+ | ±1°C, SMBus-Compatible Remote/Local Temperature Sensor with Overtemperature Alarm |
| MAX6642YATT98+T | ±1°C, SMBus-Compatible Remote/Local Temperature Sensor with Overtemperature Alarm |
| MAX6643LBBAEE+T | Automatic PWM Fan-Speed Controllers with Overtemperature Output |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6642ATT94+ | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 2-WIRE 6TDFN EP - Rail/Tube |
| MAX6642ATT94+T | 功能描述:板上安装温度传感器 SMBus-Compatible Temperature Sensor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6642ATT94-T | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6642ATT96+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX6642ATT96-T | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。