- 您现在的位置：买卖IC网 > PDF目录67800 > MAX6642ATT94+T (MAXIM INTEGRATED PRODUCTS INC) ±1°C, SMBus-Compatible Remote/Local Temperature Sensor with Overtemperature Alarm PDF资料下载
参数资料
| 型号： | MAX6642ATT94+T |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 温度/湿度传感器 |
| 英文描述： | ±1°C, SMBus-Compatible Remote/Local Temperature Sensor with Overtemperature Alarm |
| 中文描述： | DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 1Cel, SQUARE, SURFACE MOUNT |
| 封装： | 3 X 3 MM, 0.80 MM HEIGHT, MO-229WEEA, TDFN-6 |
| 文件页数： | 10/14页 |
| 文件大小： | 213K |
| 代理商： | MAX6642ATT94+T |
Detailed Description
The MAX6642 is a temperature sensor for local
and remote temperature-monitoring applications.
Communication with the MAX6642 occurs through the
SMBus-compatible serial interface and dedicated alert
pins. ALERT asserts if the measured local or remote
temperature is greater than the software-programmed
ALERT limit.
The MAX6642 converts temperatures to digital data
either at a programmed rate of eight conversions per
second or in single conversions. Temperature data is
represented by 8 data bits (at addresses 00h and 01h),
with the LSB equal to +1°C and the MSB equal to
+128°C. Two additional bits of remote temperature data
are available in the “extended” register at address 10h
and 11h (Table 2) providing resolution of +0.25
°C.
ADC and Multiplexer
The averaging ADC integrates over a 60ms period
(each channel, typ), with excellent noise rejection.
The multiplexer automatically steers bias currents
through the remote and local diodes. The ADC and
associated circuitry measure each diode’s forward volt-
age and compute the temperature based on this volt-
age. Both channels are automatically converted once
the conversion process has started, either in free-run-
ning or single-shot mode. If one of the two channels is
not used, the device still performs both measurements,
and the user can ignore the results of the unused chan-
nel. If the remote-diode channel is unused, connect
DXP to GND rather than leaving DXP open.
The conversion time per channel (remote and internal)
is 125ms. If both channels are being used, then each
channel is converted four times per second. If the
external conversion-only option is selected, then the
remote temperature is measured eight times per sec-
ond. The results of the previous conversion are always
available, even if the ADC is busy.
Low-Power Standby Mode
Standby mode reduces the supply current to less than
10A by disabling the ADC and timing circuitry. Enter
standby mode by setting the RUN bit to 1 in the config-
uration byte register (Table 4). All data is retained in
memory, and the SMBus interface is active and listen-
ing for SMBus commands. Standby mode is not a shut-
down mode. With activity on the SMBus, the device
draws more supply current (see the
Typical Operating
Characteristics). In standby mode, the MAX6642 can
be forced to perform ADC conversions through the
one-shot command, regardless of the RUN bit status.
If a standby command is received while a conversion is
in progress, the conversion cycle is truncated, and the
data from that conversion is not latched into a tempera-
ture register. The previous data is not changed and
remains available.
Supply-current drain during the 125ms conversion peri-
od is 500A (typ). In standby mode, supply current
drops to 3A (typ).
SMBus Digital Interface
From a software perspective, the MAX6642 appears as
a set of byte-wide registers that contain temperature
data, alarm threshold values, and control bits. A stan-
dard SMBus-compatible 2-wire serial interface is used
to read temperature data and write control bits and
alarm threshold data.
The MAX6642 employs four standard SMBus protocols:
Write Byte, Read Byte, Send Byte, and Receive Byte.
(Figures 1, 2, and 3). The shorter Receive Byte protocol
allows quicker transfers, provided that the correct data
MAX6642
±1°C, SMBus-Compatible Remote/Local
Temperature Sensor with Overtemperature Alarm
_______________________________________________________________________________________
5
Pin Description
PIN
NAME
FUNCTION
1VCC
Supply Voltage Input, +3V to +5.5V. Bypass VCC to GND with a 0.1F capacitor. A 47
Ω series resistor is
recommended but not required for additional noise filtering.
2
GND
Ground
3
DXP
Combined Remote-Diode Current Source and ADC Input for Remote-Diode Channel. Place a 2200pF
capacitor between DXP and GND for noise filtering.
4
SCLK
SMBus Serial-Clock Input. May be pulled up to +5.5V regardless of VCC.
5
SDA
SMBus Serial-Data Input/Output, Open Drain. May be pulled up to +5.5V regardless of VCC.
6
ALERT
SMBus Alert (Interrupt) Output, Open Drain.
ALERT asserts when temperature exceeds user-set limits. See
the
ALERT Interrupts section.
—EP
Exposed Pad. Internally connected to GND. Connect to a PCB ground pad for optimal performance. Not
intended as an electrical connection point.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6642ATT98+T | ±1°C, SMBus-Compatible Remote/Local Temperature Sensor with Overtemperature Alarm |
| MAX6642YATT98+ | ±1°C, SMBus-Compatible Remote/Local Temperature Sensor with Overtemperature Alarm |
| MAX6642YATT98+T | ±1°C, SMBus-Compatible Remote/Local Temperature Sensor with Overtemperature Alarm |
| MAX6643LBBAEE+T | Automatic PWM Fan-Speed Controllers with Overtemperature Output |
| MAX6644LBAAEE+T | Automatic PWM Fan-Speed Controllers with Overtemperature Output |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6642ATT96+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX6642ATT96-T | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6642ATT98 | 制造商:Maxim Integrated Products 功能描述:1 C SMBUS-COMPATIBLE REMOTE/LOCAL TEMPERATURE SENSOR WITH O - Rail/Tube |
| MAX6642ATT98+ | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL 2-WIRE 6TDFN EP - Rail/Tube |
| MAX6642ATT98+T | 功能描述:板上安装温度传感器 SMBus-Compatible Temperature Sensor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。