- 您现在的位置：买卖IC网 > PDF目录19362 > MAX6663AEE+T (Maxim Integrated)IC TEMP MON FAN CNTRL 16-QSOP PDF资料下载
参数资料
| 型号： | MAX6663AEE+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 10/24页 |
| 文件大小： | 297K |
| 描述： | IC TEMP MON FAN CNTRL 16-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 风扇控制，温度监控器 |
| 传感器类型： | 内部和外部 |
| 感应温度： | -40°C ~ 125°C，外部传感器 |
| 精确度： | ±2°C 本地（最大），±3°C 远程（最大） |
| 拓扑： | ADC，多路复用器，寄存器库，测速计 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 带卷 (TR) |
Temperature Monitors and
PWM Fan Controllers
10 ______________________________________________________________________________________
INT is an open-drain digital output that reports the sta-
tus of temperature interrupt limits and fan out-of-limit
conditions. Set bit 1 of configuration register 1 (00h) to
1 to enable INT output or reset this bit to zero to disable
the INT output function. Status register 1 contains sta-
tus information for the conditions that cause INT to
assert. Reading status register 1 resets INT, but INT is
reasserted if the fault condition still exists. Connect a
10k& pullup resistor between INT and V
CC
.
SDL and SDR are open-drain digital outputs on the
MAX6653 that can be used to shut the system down
based on the local (die) temperature of the MAX6653 or
the temperature of the remote sensor, respectively. The
trip thresholds for SDL and SDR are normally set above
the THERM and INT limits. Their power-up values are
set by the CRIT1 and CRIT0 pins, as shown in Table 1.
Fan-Speed Control
The MAX6653/MAX6663/MAX6664 fan-control section
can operate in one of three modes depending on the set-
ting of bit 7 to bit 5 of configuration register 1 (00h).
Regardless of the mode of operation, the PWM output fre-
quency is programmable, and the fan speed is measured
with the result stored in the fan-speed register (08h).
PWM Output Frequency
The PWM output frequency is programmed by bit 5, bit
4, and bit 3 of the fan characteristics register (20h),
regardless of the mode of operation. See Table 7.
Fan-Control Mode
The mode of fan-speed control operation is set by bit 7,
bit 6, and bit 5 in configuration register 1 (00h), as
shown in Table 8.
PWM Duty-Cycle Fan-Control Mode
Bits [3:0] of the fan-speed configuration register set the
PWM duty cycle. See Table 9 for more details.
RPM Select Fan-Control Mode
In RPM select mode, the MAX6653/MAX6663/MAX6664
adjust their PWM output duty cycle to match a selected
fan speed measured by a tachometer count value. Before
selecting this mode by setting bits [7:5] of configuration
register 1 (00h) to 0x1, the desired tachometer count
value should be written to the fan tachometer high-limit
register (10h). In this mode, the MAX6653/MAX6663/
MAX6664 are not able to detect underspeed fan faults
because the fan tachometer high-limit register (10h) func-
tions as the target tachometer count.
The MAX6653/MAX6663/MAX6664 detect fan stall
faults by comparing the fan-speed reading to the full-
scale constant of 254 (FEh). Therefore, the
MAX6653/MAX6663/MAX6664 signal a fan fault when
the fan-speed reading is 255 (FFh). Note that the RPM
mode cannot be used for speeds below 10% of the
fans maximum speed. It is important to verify that a fan
works properly at lower RPM values if a low-RPM oper-
ation in this mode is desired.
Bits [7:5]
MODE OF OPERATION
DESCRIPTION
0x0
PWM duty-cycle mode
Directly program the PWM duty cycle by writing to bits [3:0] of the fan-speed
configuration register (22h).
0x1
RPM select mode
Program the desired fan speed by writing to the fan tachometer high-limit register
(10h). This value should be written after selecting the RPM mode. The
MAX6653/MAX6663/MAX6664 then adjust the PWM duty cycle to cause the fan to
spin at the programmed speed.
100
Automatic mode
PWM duty cycle is automatically controlled by the remote temperature.
111
Automatic mode
PWM duty cycle is automatically controlled by both the remote and the local
temperatures. See the Automatic Fan-Control Mode section.
Table 8. Setting the Fan-Speed Control Mode (Default = 100)
FAN CHARACTERISTICS REGISTER
(20H) POR = 011
BIT 5
BIT 4
BIT 3
PWM
FREQUENCY
(Hz)
0
0
0
11.7
0
0
1
15.6
0
1
0
23.4
0
1
1
31.25
1
0
0
37.5
1
0
1
46.9
1
1
0
62.5
1
1
1
93.5
Table 7. Setting PWM Output Frequency
相关PDF资料 |
PDF描述 |
|---|---|
| DSP56303VF100 | IC DSP 24BIT 100MHZ 196-BGA |
| BAS21LT3G | DIODE SWITCH 250V 200MA SOT-23 |
| VI-B6Y-CW-F2 | CONVERTER MOD DC/DC 3.3V 66W |
| RBM12DCTN | CONN EDGECARD 24POS DIP .156 SLD |
| DSP56303AG100R2 | IC DSP 24BIT 100MHZ 144-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6664AEE | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6664AEE+ | 功能描述:板上安装温度传感器 Temperature Monitor & PWM Fan Controller RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6664AEE+T | 功能描述:板上安装温度传感器 Temperature Monitor & PWM Fan Controller RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6664AEE-T | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6664AEE-TG075 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。