- 您现在的位置：买卖IC网 > PDF目录19380 > MAX6670AUB50+T (Maxim Integrated)IC TEMP SENSOR REMOTE 10-UMAX PDF资料下载
参数资料
| 型号： | MAX6670AUB50+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 5/8页 |
| 文件大小： | 217K |
| 描述： | IC TEMP SENSOR REMOTE 10-UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 风扇控制，温度监控器 |
| 传感器类型： | 外部 |
| 感应温度： | 50° C 跳闸点 |
| 精确度： | ±2.2°C（最小值） |
| 拓扑： | 风扇控制 |
| 输出类型： | 数字 |
| 输出警报： | 是 |
| 输出风扇： | 是 |
| 电源电压： | 3 V ~ 3.6 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-µMAX |
| 包装： | 带卷 (TR) |
trip temperature. As the cooling fan operates, the cir-
cuit board temperature should decrease, which causes
the external P-N junctions temperature to decrease.
When the P-N junctions temperature is equal to the trip
threshold minus the hysteresis, the FANOUT pin turns
the fan off, removing power from the fan. For the
MAX6670, HYST is a three-level logic input for control-
ling the fan-drive comparators hysteresis. Connect
HYST to GND to select 4癈 hysteresis, to V
DD
to select
12癈 hysteresis, or leave floating to select 8癈 hystere-
sis. The MAX6668 has a built-in hysteresis of 8癈. This
allows the amount of hysteresis to be matched to the
cooling and noise requirements of the system. Figure 1
shows the temperature trip threshold hysteresis.
Applications Information
Remote-Diode Selection
The MAX6668/MAX6670 directly measure the die tem-
perature of CPUs and other ICs that have on-board tem-
perature-sensing diodes (see Typical Operating Circuit)
or they can measure the temperature of a discrete
diode-connected transistor. For best accuracy, the dis-
crete transistor should be a small-signal device with its
collector and base connected together. Several satisfac-
tory discrete sensing transistors are shown in Table 1.
The sensing transistor must be a small-signal type with
a relatively high forward voltage. Otherwise, the DXP
input voltage range may be violated. The forward volt-
age at the highest expected temperature must be
greater than 0.25V at 10礎, and at the lowest expected
temperature, forward voltage must be less than 0.95V
at 100礎. Do not use large power transistors. Also,
ensure that the base resistance is less than 100&. Tight
specifications for forward current gain (50 < B
F
< 150,
for example) indicate that the manufacturer has good
process controls and that the transistors have consis-
tent V
BE
characteristics.
Noise-Filtering Capacitor
In noisy environments, high-frequency noise can be
attenuated using an external 2200pF capacitor located
at the DXP and DXN pins. Larger capacitor values may
be used for additional filtering, but do not exceed
3300pF; excessive capacitance increases error. Figure
2 shows the recommended DXP/DXN PC traces.
Bypassing and Layout
The location of the remote-sensing junction in the sys-
tem affects the MAX6668/MAX6670s operation. When
using a discrete temperature-sensing transistor, place
the sensing junction close to major heat-generating
components, such as a high-speed CPU or a power
device.
To minimize noise and other errors, follow the guide-
lines below:
1) Place the MAX6668/MAX6670 as close as possible to
the remote diode. In a noisy environment, such as a
computer motherboard, this distance can be 10cm to
20cm (typ) or more as long as the worst noise
sources (such as CRTs, clock generators, memory
buses, and ISA/PCI buses) are avoided. In general,
minimize the distance to the remote-sensing junction.
2) Do not route the DXP/DXN traces next to the deflec-
tion coils of a CRT. Also, do not route the traces
across a fast memory bus, which can introduce
+30癈 error or more, even with good filtering.
3) Route the DXP and DXN traces in parallel and in
close proximity to each other, away from any high-
voltage traces, such as +12VDC. Avoid leakage cur-
rents from PC board contamination, since a 20M&
leakage path from DXP to GND causes about +1癈
error.
4) Connect guard traces to GND on either side of the
DXP/DXN traces (Figure 2). With guard traces in
place, routing near high-voltage traces is no longer
an issue.
5) Route through as few vias and crossunders as possi-
ble to minimize copper/solder thermocouple effects.
6) Use wide traces where possible. Narrow traces are
more inductive and tend to pick up radiated noise.
7) Do not use copper as an EMI shield. Only ferrous
materials such as steel work well. Placing a copper
ground plane between the DXP/DXN traces and
other traces carrying high-frequency noise signals
does not help reduce EMI.
The MAX6668/MAX6670s PGND is the ground return
for the fan driver. Bypass V
DD
to GND with a 1礔
capacitor located as close to V
DD
as possible. Add
additional bypass capacitors for long V
DD
and GND
lines.
Remote Temperature Switches with Integrated
Fan Controller/Driver
_______________________________________________________________________________________ 5
MANUFACTURER
MODEL NO.
Central Semiconductor (USA)
CMPT3904
ON Semiconductor (USA)
2N3904, 2N3906
Rohm Semiconductor (USA)
SST3904
Samsung (Korea)
KST3904-TF
Siemens (Germany)
SMBT3904
Zetex (England)
FMMT3904CT-ND
Table 1. Remote-Sensor Transistor
Manufacturers
相关PDF资料 |
PDF描述 |
|---|---|
| MC7824CT | IC REG LDO 24V 1A TO220AB |
| GBC07DRTS | CONN EDGECARD 14POS DIP .100 SLD |
| ABE35DHRR | CONN CARD EXTEND 70POS 1MM SLD |
| RSC35DRSD-S273 | CONN EDGECARD 70POS DIP .100 SLD |
| 1-1634218-2 | CONN D-SUB PLUG 9POS VERT GOLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6670AUB55 | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6670AUB55+ | 功能描述:板上安装温度传感器 Remote Temperature Switch RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6670AUB55+T | 功能描述:板上安装温度传感器 Remote Temperature Switch RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6670AUB55-T | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6670AUB60 | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。