- 您现在的位置：买卖IC网 > PDF目录19365 > MAX6683AUB+T (Maxim Integrated)IC TEMP SENSOR MON 10-UMAX PDF资料下载
参数资料
| 型号： | MAX6683AUB+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 8/14页 |
| 文件大小： | 0K |
| 描述： | IC TEMP SENSOR MON 10-UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 温度监控系统（传感器） |
| 传感器类型： | 内部 |
| 感应温度： | -40°C ~ 125°C |
| 精确度： | ±3°C（最小值） |
| 拓扑： | ADC，多路复用器，寄存器库 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 无 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-uMAX |
| 包装： | 带卷 (TR) |
Temperature Sensor and
System Monitor in a 10-Pin μMAX
Table 4. Configuration Register (Address 40h, Power-On Default = 08h)
BIT
NAME
READ/WRITE
DESCRIPTION
This bit controls the monitoring loop. Setting the bit to zero stops the
0
Start/Stop
R/W
monitoring loop and puts the device into shutdown mode. The I 2 C/SMBus
interface is still active during the shutdown mode. Setting the bit to 1 starts the
monitoring cycle. All high/low limits should be set before setting this bit to 1.
1
2
ALERT Enable
Reserved
R/W
—
This bit is used to enable or disable the ALERT output. Setting the bit to 1
enables the ALERT output; setting the bit to 0 disables the ALERT output.
—
This bit is used to clear the ALERT output when it is set to high. It does not
3
ALERT Clear
R/W
affect the Interrupt Status Register. The monitoring loop does not start until the
bit is set to zero.
4
5
6
Line Frequency
Select
Short Cycle
Reserved
R/W
R/W
—
This bit controls the internal clock frequency. Setting the bit to 1 changes the
clock frequency to 51.2kHz from 61.4kHz. This can improve the measurement
accuracy when the power-line frequency is at 50Hz.
This bit reduces the conversion time by a factor of 4 when it is set to 1.
—
This bit is used as a reset signal for the register initialization. The 1 of this bit
7
Reset
R/W
resets all the register values into the power-up default mode, including bit 7
itself.
Table 5. Interrupt Status Register (Address 41h, Power-Up Default = 00h)
BIT
0
1
2
3
NAME
2.5V IN -Error
1.8V IN -Error
5V IN -Error
V CC -Error
READ/WRITE
R
R
R
R
DESCRIPTION
A 1 indicates either a high or low limit has been exceeded at the 2.5V IN input.
A 1 indicates either a high or low limit has been exceeded at the 1.8V IN input.
A 1 indicates either a high or low limit has been exceeded at the 5V IN input.
A 1 indicates either a high or low limit has been exceeded at the V CC input.
A 1 indicates either a high or low limit has been exceeded at the internal
4
Temp-Error
R
temperature sensor. The conditions that generate and clear this bit depend
on the temperature interrupt mode selected by bits 0 and 1 in the
Temperature Configuration Register.
5, 6, 7
Reserved
—
—
The POR state of the T HOT register is 0101 0000 or
+80°C. The POR state of the T HYST register is 0100
0001 or +65°C.
High and low limits for the voltage inputs are stored in
registers 2Bh through 32h. If a measured voltage is less
than V LOW or greater than V HIGH , an ALERT is asserted.
The POR states of the high and low voltage limits are
1.1 and 0.9 times the nominal voltage for each input.
Interrupt Status Byte Functions
The Interrupt Status Register records temperature or
voltage fault conditions whenever a limit is exceeded
(Table 5). Bits 0 through 3 correspond to the 2.5V, 1.8V,
5V, and V CC voltage inputs and bit 4 corresponds to
the temperature. If a threshold has been crossed, the
appropriate bit contains a 1. In the default and one-time
interrupt modes, reading the status register clears the
register until a new out-of-range condition is detected.
8
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| EMA50DRMZ-S664 | CONN EDGECARD 100POS .125 SQ WW |
| AIMC-0201-2N7S-T | INDUCTOR MULTILAYER 2.7NH 0201 |
| RSM43DRKF-S13 | CONN EDGECARD 86POS .156 EXTEND |
| 1N5400RLG | DIODE STD REC 3A 50V DO201AD |
| HSM36DRYN-S13 | CONN EDGECARD 72POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6683EVKIT | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6683EVSYS | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6684ESA | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MAX6684ESA+ | 功能描述:马达/运动/点火控制器和驱动器 Fan-Failure Detector RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MAX6684ESA+ | 制造商:Maxim Integrated Products 功能描述:DETECTOR FAN-FAILURE 6684 SOIC8 制造商:Maxim Integrated Products 功能描述:DETECTOR, FAN-FAILURE, 6684, SOIC8 |
发布紧急采购，3分钟左右您将得到回复。