- 您现在的位置：买卖IC网 > PDF目录19363 > MAX6690YMEE+ (Maxim Integrated)IC TEMP SENSOR SMBUS 16-QSOP PDF资料下载
参数资料
| 型号： | MAX6690YMEE+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 14/16页 |
| 文件大小： | 149K |
| 描述： | IC TEMP SENSOR SMBUS 16-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 功能： | 温度计，恒温计 |
| 传感器类型： | 内部和外部 |
| 感应温度： | -55°C ~ 125°C，外部传感器 |
| 精确度： | ±5°C（最小值） |
| 拓扑： | ADC，多路复用器，寄存器库 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 无 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 管件 |
2癈 Accurate Remote/Local Temperature
Sensor with SMBus Serial Interface
14 ______________________________________________________________________________________
The MAX6690 incorporates collision avoidance so that
completely asynchronous operation is allowed between
SMBus operations and temperature conversions.
When autoconverting, if the T
HIGH
and T
LOW
limits are
close together, its possible for both high-temp and low-
temp status bits to be set, depending on the amount of
time between status read operations (especially when
converting at the fastest rate). In these circumstances,
it is best not to rely on the status bits to indicate rever-
sals in long-term temperature changes. Instead, use a
current temperature reading to establish the trend
direction.
Conversion Rate Byte
The conversion rate register (Table 8) programs the
time interval between conversions in free-running auto-
convert mode. This variable rate control can be used to
reduce the supply current in portable-equipment appli-
cations. The conversion rate bytes POR state is 02h
(0.25Hz). The MAX6690 looks only at the 3LSB bits of
this register, so the upper 5 bits are dont care bits,
which should be set to zero. The conversion rate toler-
ance is ?5% at any rate setting.
Valid A/D conversion results for both channels are
available one total conversion time (125ms nominal,
156ms maximum) after initiating a conversion, whether
conversion is initiated through the RUN/STOP bit, hard-
ware STBY/pin, one-shot command, or initial power-up.
Extended resolution and the parasitic resistance can-
cellation mode are available at conversion rates of 1Hz
or lower.
Slave Addresses
The MAX6690s device address can be set to one of
nine different values by pin strapping ADD0 and ADD1
so that more than one MAX6690 can reside on the
same bus without address conflicts (Table 9).
The address pin states are checked at POR only, and
the address data stays latched to reduce quiescent
supply current due to the bias current needed for high-
Z state detection.
The MAX6690 also responds to the SMBus Alert
Response slave address (see the Alert Response
Address section).
POR and UVLO
The MAX6690 has a volatile memory. To prevent
ambiguous power-supply conditions from corrupting
the data in memory and causing erratic behavior, a
POR voltage detector monitors V
CC
and clears the
memory if V
CC
falls below 2V (typ, see Electrical
Characteristics). When power is first applied and V
CC
rises above 2.0V (typ), the logic blocks begin operat-
ing, although reads and writes at V
CC
levels below 3V
are not recommended. A second V
CC
comparator, the
ADC undervoltage lockout (UVLO) comparator, pre-
vents the ADC from converting until there is sufficient
headroom (V
CC
= 2.8V typ).
BIT
NAME
POR
STATE
FUNCTION
7 (MSB)
BUSY
0
ADC is busy converting when high.
6
LHIGH
0
Internal high-temperature alarm has tripped when high; cleared by POR or readout
of the entire status byte if the fault condition no longer exists.
5
LLOW
0
Internal low-temperature alarm has tripped when high; cleared by POR or readout of
the entire status byte if the fault condition no longer exists.
4
RHIGH
0
External high-temperature alarm has tripped when high; cleared by POR or readout
of the entire status byte if the fault condition no longer exists.
3
RLOW
0
External low-temperature alarm has tripped when high; cleared by POR or readout
of the entire status byte if the fault condition no longer exists.
2
OPEN
0
A high indicates an external diode is open; cleared by POR or readout of the entire
status byte if the fault condition no longer exists.
1 or 0
RFU
0
Reserved.
Table 7. Status Byte Bit Assignments
相关PDF资料 |
PDF描述 |
|---|---|
| DSPB56721AF | AUDIO PROCESSOR SYMPH 80-LQFP |
| ESM43DRYI | CONN EDGECARD 86POS DIP .156 SLD |
| DB9W4P500G00LF | CONN DSUB PLUG 9W4 R/A GOLD |
| TPSD107M020R0150 | CAP TANT 100UF 20V 20% 2917 |
| DSPB56725CAF | IC DSP 24BIT 80LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX6690YMEE+ | 功能描述:板上安装温度传感器 Remote/Local Temperature Sensor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6690YMEE+T | 功能描述:板上安装温度传感器 Remote/Local Temperature Sensor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX6691MUB | 功能描述:数据转换 IC - 多种 RoHS:否 制造商:Texas Instruments 转换器数量:1 分辨率:8 bit 工作电源电压:2.7 V to 5.5 V 功耗: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:MSOP-10 封装:Reel |
| MAX6691MUB+ | 功能描述:数据转换 IC - 多种 4Ch Thermistor Temp to-Pulse-Width RoHS:否 制造商:Texas Instruments 转换器数量:1 分辨率:8 bit 工作电源电压:2.7 V to 5.5 V 功耗: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:MSOP-10 封装:Reel |
| MAX6691MUB+T | 功能描述:数据转换 IC - 多种 4Ch Thermistor Temp to-Pulse-Width RoHS:否 制造商:Texas Instruments 转换器数量:1 分辨率:8 bit 工作电源电压:2.7 V to 5.5 V 功耗: 工作温度范围:- 40 C to + 85 C 封装 / 箱体:MSOP-10 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。